Jump to content
SAU Community

Recommended Posts

Hey guys, I need some help with the air con in my R33, I saw some other threads about air con but not this specific problem.

When I turn my air con on, the compressor turn on, idle goes up 800rpm, then a few seconds later the compressor switches itself off and idle drops to normal again. This happens driving as well, but obviously not as noticeable, except for the air not being cold. Thing is sometimes the air con works fine, esp. on the open road, and sometimes it won't stay on for a whole trip. When the compressor is on, the air is cold. It is really frustrating, on hot days I find myself playing with the controls all the time as I'm driving trying to trick the compressor into turning on.

Is it a sensor, if so which one and how can I fix it?

Is it a lack of gas?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/159596-aircon-compressor-doesnt-stay-on/
Share on other sites

Hey guys, I need some help with the air con in my R33, I saw some other threads about air con but not this specific problem.

When I turn my air con on, the compressor turn on, idle goes up 800rpm, then a few seconds later the compressor switches itself off and idle drops to normal again. This happens driving as well, but obviously not as noticeable, except for the air not being cold. Thing is sometimes the air con works fine, esp. on the open road, and sometimes it won't stay on for a whole trip. When the compressor is on, the air is cold. It is really frustrating, on hot days I find myself playing with the controls all the time as I'm driving trying to trick the compressor into turning on.

Is it a sensor, if so which one and how can I fix it?

Is it a lack of gas?

Thanks

I had the same problem in my 32, turned out being my compressor shorting out. It started off as you describe then only got worse untill it would only stay on for a minute or 2 then blow the fuse. I had to get a new second hand compressor installed. Not cheap unless you can do it yourself

I had the same problem in my 32, turned out being my compressor shorting out. It started off as you describe then only got worse untill it would only stay on for a minute or 2 then blow the fuse. I had to get a new second hand compressor installed. Not cheap unless you can do it yourself

That's not what I wanna hear :P

Dunno if it's a fuse blowing, some days it works fine. But yeah it is getting worse... or is it just cause it's summer?

mine has the same problem, not as severe i think as yours but same symptoms. AC will switch off before its time and than switch back on randomly (usually after about 30seconds or so) you can feel it while driving aswell

when i got mine re-gassed the guy said it is a sensor of some description thats behind the dash/glovebox area that senses the temperature and turns off the compressor because it thinks its reached the right temp

best to get an a/c to check it out.. he will tell u better than anyone on a forum

btw cost me approx 150 for a re-gas and new filter/dryer

try putting it in diagnostics mode.....

this will give you an indication of what is wrong....

turn car on

hold the off button for 5 secs staright away.

this should put you into teh diagnostics mode.....

check the sensore by pressing the HOT switch (red triangle)

the readout will tell you if you have a problem

20= all is ok

21= outside air sensor

22= inside air sensor

23= water temp sens

24=intake temp sens

25= sunload sens

26=PBR

27= refridgerant temp sens.

hope that helps :D

just did mine and found that my sunload sensor is f**ked....... :)

Oh well

It's only f****d if you were parked out of direct sunlight. Try shining a torch on the sensor (little "button" on the passenger side of the dashboard, near the base of the windscreen).
It's only f****d if you were parked out of direct sunlight. Try shining a torch on the sensor (little "button" on the passenger side of the dashboard, near the base of the windscreen).

was parked in the garage.....

that was what i was told to do as otherwise ^^^^

migt clean it though and see if that makes i difference :)

even a cloudy overcast day will bring up the error code for the sun sensor I doubt that is what is causing your drama though almost sounds like it might just be a loose connector if the rest of the diagnostic check is okay is it or isnt it blowing the fuse? If it is could be the clutch coil on the compressor

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
    • Thanks for taking the time to post that ! If anything changes or happens please do update us. 
    • Somehow Vertimass/Oak Ridge National Labs has figured out a catalyst that can convert ethanol into C9-C10 hydrocarbons in basically a single step without ending up with a bunch of ethylene or similar waste products: https://patents.google.com/patent/WO2023224867A1/en I still don't think anything like this will keep us from needing to transition to EVs regardless along with all kinds of other electrification, but things like this will go a long way towards alleviating the problem of how to electrify things like planes. Renewable diesel is seemingly an easier problem as well, Chevron is already running refineries for the stuff and the primary feedstock is tallow and other waste fats from agriculture.
    • Ok so I have sorted everything with my uniclutch and  i can offer up a bit of feedback and some things that might help others.    I found problems with factory damper line. Weird shit and had trouble with peddle adjustment    I used this https://au.gktech.com/products/r33-gts-t-skyline-braided-clutch-line?_pos=2&_sid=22b01b9b9&_ss=r Also when adjusting peddle leave a bit of play. You can get into a over stroke condition easy.. Make sure you can push the slave forward after adjusting to confirm fluid can return to master then you will need to pump it up heaps…..not sure why but that’s how it is.    last thing the splined adapter is machined perfectly. If your input shaft is old like mine was I would put a bit of valve grinding paste on it and stroke it like a 15 year old. Just to give it a tad more clearance and to better match it to the spline.    reason is on a near flat shift I have had situation where the peddle returns a millisecond after you lift from the clutch. No slip or anything but I reckon this is due to tolerance on the spline being way tighter than stock clutch and binding for a sec. I think this will go away but also my spline was old. Box is old so I guess I should have checked better. It’s a super neat fit.    it feels light as and holds awesome without any noise    
    • My Fuga Hybrid is JDM, 2014 model but very similar to the V37 from the looks of things..same platform just physically larger and very comfortab;e
×
×
  • Create New...