Jump to content
SAU Community

Recommended Posts

Hi guys,

I have just gotten my hands on a used Power FC for my series II and it has been already tuned to a Skyline with similar mods. So i have put it in just to test that everything is working ok.

My question is to those of you running a Power FC what is a safe knock level? I haven't

driven the car too hard because of this. And also not knowing who tuned it.

Oh and don't worry it will be re-tuned once i have the turbo upgrade.

So any one who can help, i'm all ears!

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/
Share on other sites

Thanks guys. Well it hasn't been anywhere 40 yet. There's just not much point having a gauge

or meter in your car when you don't know whats good and bad :worship:.

I gave it a bit of a stab the other day on lower boost and it shot up just over 30.

So that kinda freaked me out not knowing if that was ok or if i had just hurt my car.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2971436
Share on other sites

not always a definative thing the knock reading....Just look for consistant reads say above 30-40 if this is happening then I would get your tune looked at. If your running under 20 all the time with an occasional hic-up I wouldt be too stresed.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2972071
Share on other sites

The warning light/engine will come on for levels that exceed 50.

The warning light/engine will come on for levels that exceed....whatever it is set to.

I actually thought the default was 60 but you can cahnge that to anything you want :sorcerer:

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2972789
Share on other sites

Your asking for trouble if your running a previously tunned ECU in any car without at least a power run or SOME type of lambda check up!!!!

Knock is ony half the equasion. I lean tune cando the same ammount of damage that detonation will.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2972812
Share on other sites

12 is too low really. If everything is working fine I like to tune into the low 30's. Obviously depending on NVH etc every car is different and as such the knock meter on the FC cant really be gospel.

Srewed up piston to bore clearances etc etc can contribute as well

There is no substitute for physically listening for detonation OR a proper knock box.

Edited by Risking
Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2972859
Share on other sites

Thanks guys for all the input. It all helps.

Like i said i will not be using it till i have the rest of the car ready for a tune. But i have half a mind to leave it in. Just this past week i have noticed it runs twice as good with stopping and going around town then the factory ECU ever did. It doesn't seem to be any more savage on the fuel side of things either. But yes i am also cautious about the air/fuel ratio.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2976031
Share on other sites

I put my PFC in a few weeks ago, and I am due to get it tuned in the next week or so. I was trying to really drive it like a granny because the knock reading was really bad (hope I haven't damamged the engine!). Even though I was trying to use less than 25% throttle and even less up hills and on hot days, I hit 203 once! :laugh: And 120-130 a couple of other times. Never really heard any pinging though.

Anyway I just turned down the boost to 7psi and it is now drivable again with reasonable knock levels (stays under 25 mostly). Can't wait to get it tuned though so I can crank the boost up again, it feels so slow now.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2976147
Share on other sites

I put my PFC in a few weeks ago, and I am due to get it tuned in the next week or so. I was trying to really drive it like a granny because the knock reading was really bad (hope I haven't damamged the engine!). Even though I was trying to use less than 25% throttle and even less up hills and on hot days, I hit 203 once! :laugh: And 120-130 a couple of other times. Never really heard any pinging though.

Anyway I just turned down the boost to 7psi and it is now drivable again with reasonable knock levels (stays under 25 mostly). Can't wait to get it tuned though so I can crank the boost up again, it feels so slow now.

So you installed your Power FC and you have been driving around on the base map?

Reallly not a smart idea.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2976648
Share on other sites

So you installed your Power FC and you have been driving around on the base map?

Reallly not a smart idea.

As I said I was only on about 25% throttle, and I monitored the knock reading constantly. A couple of times I did push it a bit too far which was silly. Now that I have decreased the boost a bit I think it now is running better than ever so the base tune can not be that bad in this case any way. Anyway I just can't wait to get it tunes, but have not been able to yet as I have had to do several other things to the car first.

Link to comment
https://www.sau.com.au/forums/topic/160008-apexi-power-fc/#findComment-2977204
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sadly I can confirm if you are actually seeking to drift, you will quite easily spin up one wheel. Even if you're going in a straight line. I am not entirely sure of the metrics/terminology here but there's only a certain amount that the helical will actually spin both wheels. I've seen it on video with my own car where two lines of smoke switch over to just one after you really get in to it. Unlike with a clutch diff where you can keep your foot planted until the car regains grip, in my experience with the helical you want to be utilizing traction control allowing LIMITED slip or lifting (partially) when you start to spin up both tyres with a Nissan helical. Which makes them pretty sub optimal for drifting duty. That said... this is probably a helical on numbers alone. Just put the Kazz in
    • Let's just fix the problem by f**king the rest of the gearbox.
    • Unlikely, as per Greg's post. This is not helical diff behaviour unless one wheel is up off the ground. Shimming what? You don't "shim" a mechanical LSD. Probably not in the sense that you have heard of people "shimming" a diff. And the process that Nissan f**kwits call "shimming" a diff involves super-preloading a VLSD cartridge against the side of the diff to create a friction/wear point (in a place that it wasn't supposed to have one) to make the sloppy, useless, viscous diff into a hybrid viscous/mech abortion. In case it isn't clear, I consider the process to be stupid. Nike.
    • How much does the shifter move when the car is in gear with the engine off? If it is more than about 1cm you need to replace your shifter bush. Your shifts will just get crunchier, not faster, with a short shifter unless you also rebuild the whole box
    • I should video mine, will prob do it tomorrow    Between 1st and 3rd, you could fit another two gears. That is how loose and wobbly it is   horrible:(
×
×
  • Create New...