Jump to content
SAU Community

Recommended Posts

hey guys

well i just finished locking my hi-cas but my power steering has basically dissappeared and is now very heavy to drive. I used this method http://www.nissansilvia.com/forums/locking...13-t185697.html down to every last step (this was definitely the easiest and best explaination of what to do out of the 3 tutorials i've seen) the only thing i did different was i also pulled out the hicas computer under the parcel shelf in the boot which it doesn't say to do but surely that couldn't be part of my problem now that i have no 4ws?

And yes before anyone asks there is the right amount of power steering fluid in the car, i topped it up!

anyone got any ideas?

Also the power steering pump i think was making a wierd noise for about 2 minutes when i started the car for the first time but i presume thats because the power steering fluid had to go through the system again?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

There are no electrical connections to the power steering pump that I can see.

The only electrical connection seems to be to the solenoid on the power steering rack.

So, why can’t you remove the HICAS computer?

Is the power steering speed sensitive?

Does the HICAS computer vary the amount of power assist by varying the amount of steering rack hydraulic assistance bypass using the solenoid?

Does the HICAS computer know the speed (via a link to the ECU)?

Does the HICAS computer open/close the solenoid depending on that speed?

Is it a simple open or close? Or does the solenoid have various amounts of bypass?

Say 0% at <20kph, 30% at 60 kph, 50% at 80 kph and 100% at >100 kph?

Is there a definitive NISSAN publication on R32/33/34 variable assist power steering?

For some time I have been contemplating removing the HICAS computer from the R32GTST. I was considering using one of the Datalogit outputs to control the power steering assist. But I need to know the solenoid parameters.

:D cheers :)

There are no electrical connections to the power steering pump that I can see.

The only electrical connection seems to be to the solenoid on the power steering rack.

So, why can’t you remove the HICAS computer?

Is the power steering speed sensitive?

Does the HICAS computer vary the amount of power assist by varying the amount of steering rack hydraulic assistance bypass using the solenoid?

Does the HICAS computer know the speed (via a link to the ECU)?

Does the HICAS computer open/close the solenoid depending on that speed?

Is it a simple open or close? Or does the solenoid have various amounts of bypass?

Say 0% at <20kph, 30% at 60 kph, 50% at 80 kph and 100% at >100 kph?

Is there a definitive NISSAN publication on R32/33/34 variable assist power steering?

For some time I have been contemplating removing the HICAS computer from the R32GTST. I was considering using one of the Datalogit outputs to control the power steering assist. But I need to know the solenoid parameters.

;) cheers :O

{This is from memory out of the r32 gtr service manual..}

The variable assist is done on the solenoid on the steering rack.

The varying voltage to the solenoid comes from the hicas computer. There is a speed signal that goes from the speedo cluster to the hicas computer. The force ramp is not quite linear but can be approximated as increasing with speed, graph in manual.

I am fuzzy on wether the speed signal goes through the ecu before going to the hicas module, just sure on the origin and end point.

As my copy of the manual is at home I can't confirm or deny, But I have been studying this section recently because mine has power assist issues at the moment. Car has been converted from auto to manual at some stage and wiring is all up the duff.

If any of this helps at all...

James.

*edit for v vs f.. f increases. Fairly sure v decreases.

Edited by heller44
{This is from memory out of the r32 gtr service manual..}

The variable assist is done on the solenoid on the steering rack.

The varying voltage to the solenoid comes from the hicas computer. There is a speed signal that goes from the speedo cluster to the hicas computer. The force ramp is not quite linear but can be approximated as increasing with speed, graph in manual.

I am fuzzy on wether the speed signal goes through the ecu before going to the hicas module, just sure on the origin and end point.

As my copy of the manual is at home I can't confirm or deny, But I have been studying this section recently because mine has power assist issues at the moment. Car has been converted from auto to manual at some stage and wiring is all up the duff.

If any of this helps at all...

James.

*edit for v vs f.. f increases. Fairly sure v decreases.

Thanks James.

The R32 speedo cable (mechanical) goes to the speedo, then electronic to the ECU.

Solenoid voltage......maybe duty cycle? Using the variation in duty cycle to provide different levels of assist.

Time to stick a meter on the solenoid, jack the rear wheels up, try various kph and see what happens to the solenoid.

If solenoid pulsing is the case then I could use a Jaycar digital pulse controller (similar circuit to IEBC) with the speedo pulse as the input. But I might as well leave the HICAS computer in, they weigh about the same. I have already pulled the warning light bulb, so no gain there. The only thing I could do is program my own levels of power assist.

;) cheers :O

No worries.

I'll look at the manual when i get home. There is a fairly comprehensive writeup on the variable assist in there.

mr_rbman: thats about what you'll have to do to keep it. Others I have seen trying to strap the solenoid have just had either very heavy or very light steering. Just letting the system do its job is the best way.

I'm currently missing a clutch switch input and neutral switch input to the hicas computer.. without those two I can't even get into the diagnostics mode... ;) But hey, I might be chasing wiring.. but at least I gained a 26.

James.

Edited by heller44

An alternative to removing the bulb from the dash is cutting one wire on the smaller of the two plugs into the hicas computer. It is green with white trace line, and is in the bottom left corner. I found this easier than removing the dash to pull the bulb out and the light will still come on if you have low power steering fluid.

You can also just leave the smaller plug out and it has the same effect, I didn't notice anything else going wrong when I did that.

Voltage:

0 km/h (0 MPH) : Approx. 4.4 - 6.6V

100 km/h (62MPH) : Approx. 1.5 - 2.2V

This is the value range that it should be delivered to the solenoid. According to the manual.

Still unsure if it a pwm signal or a variable dc. IF it is a straight solenoid function, it would be a pwm, which a digital meter would just be reading the rms of the pulses.

The speed signal from the speedo gauge goes to the ecu and to the power steering control unit (which is housed in the hicas module, thats why it has a seperate smaller plug. ie. what salad said above ^ ).

Thats an idea.. Might do some diagnosis this weekend, bring the cro home and have a look-see..

James.

Edited by heller44

The smaller plug by itself on non-hicas cars contains all the wiring for the power steering control.

The smaller plug on the hicas equipped cars has the hicas solenoid outputs, hicas failsafe output and hicas warning light, so it could be left unplugged after the hicas unit is locked.

The larger plug contains all the inputs and the power steering output.

The wiring diagrams show the same plug shape used for hicas and non-hicas, just wiring changed.

James.

Voltage:

0 km/h (0 MPH) : Approx. 4.4 - 66V

100 km/h (62MPH) : Approx. 1.5 - 2.2V

This is the value range that it should be delivered to the solenoid. According to the manual.

Still unsure if it a pwm signal or a variable dc. IF it is a straight solenoid function, it would be a pwm, which a digital meter would just be reading the rms of the pulses.

The speed signal from the speedo gauge goes to the ecu and to the power steering control unit (which is housed in the hicas module, thats why it has a seperate smaller plug. ie. what salad said above ^ ).

Thats an idea.. Might do some diagnosis this weekend, bring the cro home and have a look-see..

James.

Hi James, thanks for that info. Would I be right in assuming 6.6 volts (not 66 volts)?

From memory (always risky) doesn't 14 volts DC cycled at 20hz = 4 volts?

So it is most likely a pulsing solenoid, something like lower voltage = lower frequency = higher bypass

:w00t: cheers :O

Sorry about that. Finger fault. 4.4v-6.6v

The voltage measured could be a function of an decrease in the frequency, or an decrease in duty cycle, or an decrease in voltage. If I had to bet, I'd say an decrease in duty cycle would be the more likely, easier to pwm the signal than try and vary the frequency.

I was toying with the idea of a variable resistor but then that would be static, I'm also not convinced it's a safe thing to do.

I'm scared of just putting a backing plate on because the Nissan part is really flatly machined, I also don't want super light steering.

SKid - was the way you were planning to do it based around replicating the stock HICAS computer's adjustment based on speed?

I was toying with the idea of a variable resistor but then that would be static, I'm also not convinced it's a safe thing to do.

I'm scared of just putting a backing plate on because the Nissan part is really flatly machined, I also don't want super light steering.

SKid - was the way you were planning to do it based around replicating the stock HICAS computer's adjustment based on speed?

Jaycar have a kit called a Digital Pulse Adjuster (much the same as the IEBC). It can read the pulse signal from the speedo input to the ECU. You can then program in your own output to the bypass solenoid. For example, up to 20 kph you might want 1hz of pulsation (bypass) so that there is lots of power steering assistance. At say 50 kph you might want 5hz, so that there is less assistance. Then at say 100 kph you might want to turn the power assistance pretty much off. The DPA has 128 load points, so you could vary the power assistance every 2 or 3 kph if you wanted. Or just step it down every 10kph or so. Basically you would get to choose your own power assistance curve.

Keep in mind that I have guessed the 1hz, 5hz etc, you would have to test it yourself in the real world and determine what works. But that is pretty easy, same as tuning the IEBC for boost, you just fiddle with the bypass map until you get the curve you want. Have a read of the DFA & IEBC thread in the Stagea section for some details on the kits.

:glare: cheers :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • At SMSP, I mainly see Hondas, M cars, A90 Supras and of course, plenty of Evos. Have not seen a single R32 ro R34 Skyline on the night sessions that I've been to. That's really saying something.
    • I like mine. Much better than stock. Like i said before the reverse/parking cameras look even worse than normal, still useable. When you buy one make sure it's the latest version. Heaps of cheap ones that run the old hardware and software. Got mine from AliExpress. Mine is quick no lag, boots up 1-2 sec. Menu is fast. Netflix is fine and so is YouTube. Android Auto is random taking 3sec to 15sec. Most of the time it's quick. Very rare it doesn't connect. But that could be a phone thing.   Now I think they use a Pixel 3XL to run this whole thing which i guess is fine, but the problem is that some apps will not work on old hardware like Disney Plus  Maybe Prime Video too 🤔. they will not update. Iv'e tried getting the APK Disney + but i still couldn't get it working. I have a Data sim installed so i have internet all the time. You can't Hotspot off your phone and connect Android Auto at the same time. Not that you need too, if you want you can hotspot off your phone and run any internet map app (google maps) and you can run the Spotify app on it's own (the app runs better than android auto) You can still access the INFINITI intouch system for all the o.g stuff    P.S i got new non Polarization Sunglasses too 😎 
    • I also don't mean to rain on your parade. But with a 5-10k budget for road only? I'd want to check confirmation that everything IS working correctly and I'm with @GTSBoy for a plan of action here. I'd be checking subframes, bushes, exhaust hangers, interior bits and generally QOL things and CONFIRMING they are working right before thinking about motor. You can get 250KW+ on stock RB26 hardware by simply removing the built in restrictors and tuning the stock ECU. If you want purity that's as far to take it, which I would be worried to do and won't think the budget would allow for when earnestly checking for 30+ year old car stuff.
    • I specifically said buy new performance car because of the use case here (i.e, no track use and fun livable everything/do it all easily if not especially amazing as a drivers car). Tracking an 80K Skyline and an 80K M2 makes the BMW the obviously more risky purchase WHEN something goes wrong you suddenly can't easily fix it with hand tools and readily available parts that you may have a community of people you know available, or years of your own knowledge on the platform to apply. There's reasons you see Hondas and Vettes and RB's and Miatas and such at tracks, you can easily hand-tool repair 99.9% of it in a shed, usually with the tools and the skillset of the owner to apply to it. An i30N is not going to beat a R chassis unless it's got massive problems either. The old cars can, and still do work great. The problem is - and always has been - social media would have you believe it's simple and easy to achieve the results you see online.  People want their car to be like "one of those cool JDM cars" which is the default image people have when they think of  "cool JDM cars" You are paying 25 years of catchup R&D to achieve. Or the knowledge somebody else has to do it for you, which is big dollar restomod stuff.  The bar has been moved and every R chassis that people see/like/enjoy has 25 years of R&D thrown at it, or is owned by someone who did all that work and has that knowledge over the past 25 years. All the survivors have been progressively resto-modded the entire time. OR you slowly bring it back to how it was stock. Which is also prohibitively expensive, done for the love of it. This is what the JDM community is now. This is fine, but "Where do I start?" is either: 1) Don't 2) Take your own slow journey but you cannot compare your progress with others who have had 25 years of R&D and experience building their own cars unless you pay for it.
    • Yep, with the crazy inflation of the value of our cars these past couple of years this became a problem for me too... My solution is to transition to bikes. Everything feels so cheap compared to tracking the skyline lol
×
×
  • Create New...