Jump to content
SAU Community

Recommended Posts

hi, i am having a problem with my drivers side door.

when i park it in the rain, water gets into the door, and then when i open the door there is all this rust coloured water on my door step area.

at first i thought i may be getting rust under the back skyline plastic but when i lifted it, it was fine.

i checked and the drain holes aren't blocked :D (that would be an easy fix)

the rust coloured water seems to be escaping through the plastic at the bottom in the gap where the plasic pannel screws onto the door.

What could be rusting in the door? the door itself? or would it be the window winding mechanism? (sounds expensive)

it looks like the water is getting into the door where the glass is, the fabric stuff doesn't seem to be touching the glass.

would that be how the waters getting in?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/16033-drivers-side-door-filling-with-water/
Share on other sites

Not good.

Even if the water was getting in the door from where the window is, it still should drain straight out the bottom.

Pull the door trim off and have a good look in there. There must be something in there blocking one or some of the holes :D

That's all I can think of :(

J

The creeking noise from the window is a common thing on Skylines - it's normally just loose bolts on the mechanism - you need to remove the door panel to fix.

Over time the rubber/fabric guide wears. It should push up against the glass, if it doesn't water, dirt and anything else can easily get inside the door.

I'd suggest having the door panel removed so that you can fix the creeking window, check for any rust/damage and replace the fabric guide...

Cheers

Dave

I think that the windows are one of the weaker points of Skylines, particularly since they use a frame-less design. The glass has to be pressured against the rubber trim in order to form a water-tight seal and I think this causes problems.:P

I had a similar problem on my old car when I first got it and it was only 6 years old at the time...;)

Still, having the door panels removed aint that much a job and I took the opportunity to have some better speakers installed along with a load of sound deadening material too:D

guys i had that water problem with my old car it wasnt a skyline i found that when the tint guys did my window all the access tint shit sat on the bottom of the doors and got stuck

alot of shit can stay down there i reconmend you get your self a screw driver open the trim put some water down and see how you go

should be fine =)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reading your posts Josh, sometimes I feel like I've gone in a time machine back to the 90's when everyone was doe-eyed and figuring things out for the first time.  I've lost track of how many single turbo GTR's I've seen on track that haven't burnt down lol. Everything has been figured out a long time ago. These things are at the point now where its essentially turn-key to go single turbo. 
    • Among other things yes. Making sure to either use an oil pressure regulator or the right restrictor size for your oil pump/range of oil viscosities you intend to run, making sure you plumb the lines correctly, turbo should be placed such that it siphons properly even when the water pump isn't turning so you don't boil coolant in the turbo after shutdown, oil return should be low resistance and also preferably picking the one that is most likely to return to the pickup as opposed to some other irrelevant part of the pan. It's far from impossible to figure this out but I have seen people really, really struggle and if that's the case it's easier to just take the path of least resistance. To me, bolt-on twin turbos are a fixed cost whereas single turbo is almost unbounded.
    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
×
×
  • Create New...