Jump to content
SAU Community

Recommended Posts

Hey :(

Well i have in general... a problem... :( as alot of ppl do but shouldnt... so if anyone can help me would be much appreciated...

Its an R32 Skyline GTST .... Ok... so i just had my car in to a place called APC in springwood... i got my timing belt done, all the other belts at the front done, new spark plugs, injector flush, throttle body cleaned, new fuel pump, dyno'd etc....

has been all good for about 2 weeks... until now...

i was driving along 2 nights ago and just all of a sudden the revs started dying, and then it picked up... then they started to die again... and way kept my fooot on the gas while it was doing it and the whole car just started to stop go stop go stop go... like shaking... so i pulled over... and the engine conked out... so im like WTF?

start her up and she was fine for about 2 or 3 minutes... then it did it again and again... and then i pulled up at a set of lights and the idle had a mind of its own... revving till about 2000 / 2500 RPM then going to idle, reving idle reving idle just reving by itself...

so like i pull over and turn the bitch off... and wait a minute,.. and turn it back on... and its fine... for another few minutes...

so u could say its hunting i spose... i think thats the term u use for when it revs on its own....

and it doesnt do it at all when its cold or just warmed up... more or less after its been for a drive for more then 10 or 15 mins...

kinda weird.... i was thinkin 02 sensor.... or TPS.... or idle speed motor... or a vacuum leak somewhere...

maybe someone can narrow it down for me :laugh: or tell me where these things are and what to do to check them out

Thanks heaps guys

-Josh

Link to comment
https://www.sau.com.au/forums/topic/160616-r32-revs-by-itself/
Share on other sites

huumm actually this happens to my car as well now...but more severe, it's getting very consistent...on my post ppl suggest intercooler pipe leak, clean afm..I clean the afm still same thing happened...checking in workshop on Monday...I'll keep you posted...do tell me if you figure out what is wrong as well

yeah the fuel filter isnt that old either... maybe like 10 mnths old or something? but fuel pump was just done... and it was on the dyno... and i only fill up using vortex 98 or shell v-power.... so i dont think i would have got a bad batch of fuel... ok has anyone got an engine manual or e book on the RB20DET... im not completely null minded of engines etc but i honestly dont know where the aac valve is.... or the 02 sensor... unless your talkin about the one under the car on the exhaust system? and i assume your talking about the ECU behind the dash?

yeah no problem dude... ill let you know of any progresses :ermm:

hey mate, have you tried resoldering the joints inside the afm or just cleaned the plug out with contact cleaner? i spent a thousand bucks chasing a missfire/idle prob and i eventually fixed it myself for nuthin. pulled the afm apart and resoldered the joints inside. runs perfect now.

yeahhh i had a mate of a mate come over and reset the error codes on the computer which was air flow meter

so i got a can of carby clean and tightened the pins in the connector and i sprayed the crap out of the little square element inside the air flow meter and runs great now :unsure:

cheap fix :P

anyone know antything about if its worth getting bigger air flow meter... say like the Q90 from a 300ZX i think it is... and i think theres a bigger one again?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From my bolts, standard M8 with 1.25mm thread pitch (M8x1.25mm).    Length is 19mm under the head and has a captive 18mm OD flat washer.   20mm length from a bolt shop is what you'll be able to get.   Make sure they're zinc plated.    If you're concerned about strength, grade 8.8 will be more than enough. Original PN is 01121-04971.  Now discontinued according to Amayama but that's because it's one of the parts that's been captured by the Heritage program, which explains the ridiculous price.   New PN is 01121-RHR20: https://nismodirect.com/nismo-heritage-bolt-pin-hinge-hood-bnr32-nissan-skyline-gt-r-01121-rhr20-01121-04971/ About AUD33 converted from Yen in the above link but that's just one example. Interesting that the hinge-to-body bolts are still available non-heritage.....PN 08116-8161G around $2 each (amayama).    Same thread but 16mm long.
    • Well, if that filter was impeding fluid flow, then it could have similar effects to faulty solenoids. The TCU will register a fault when it does something (ie, changes the state of a solenoid) and does not detect the required result. If there are other causes that can make the same lack of result, then they will be indistinguishable to the expected cause for which the TCU has a code.
    • Yellowjackets, red ones, blue ones (other than Splitfire) have all been demonstrated to be unreliable on turbo engines. That unreliability can be anything from outright failure (ie, 4 out of a set of 6 working out of the box) to just not being strong enough for the task, on a boosted engine. Not enough of us care about NA engines to know whether that unreliability is an issue for the undemanding needs of an NA RB20. I should think though that the DIS-008 should fit the 20. There's not really any reason for the head/coil mounting area to be any different on those 2 Neos. I wouldn't be buying Splitfires, or any other old tech coilpack, for a car in this day and age though. I would buy modern pencil coils and do what needs to be done to adapt them to the loom. That's relatively trivial these days, with numerous kits for fitting R35, or Audi, or Yaris/Corolla coils.
    • Keen to see how much work is needed to get an abandoned Skyline going. My R32 has been sitting idle for three years or so but finally got some time to get it going again. (Also lurking SAU and trying to hit 10 posts so I can start my own intro thread with pics)
    • Hi. Which coilpacks can i use in my engine? I looked at the Splitfire but the closest "match" i found was SP-DIS-008 but even that they do not show RB20DE NEO so iam not 100% sure. Or maybe different one which will 100% work? I saw many on ebay but they are some cheap "strange" ones. What about Yellow Jackets? Many thanks 🙂 
×
×
  • Create New...