Jump to content
SAU Community

Recommended Posts

well i got my rb25det r31 and it free revs well.

But once you put load on it driving it starts to rev and then breaks down and wont rev, and starts backfiring as if it was a limiter noise...

when you change gears the bov makes a high pitched whistle instead of the normal rb25det bov noise, but thats in 1st and 2nd but from 2nd to 3rd and 3rd to 4th and 4th to 5th it makes the normal noises...

and when you do the limiter revving under load noise when you put the clutch in the revs drop down then it revs back up

free revs all the way out but wont rev under load

what could it be?

Link to comment
https://www.sau.com.au/forums/topic/160907-rb25det-breaks-down-under-load/
Share on other sites

coil packs or spark plugs. there are a few different fixes for the misfiring problem.

#1 - gap your spark plugs to .8mm (do that if not already done)

#2 - fix your coil packs, there are a few threads around on how to do this.

as for the bov sound, im not too sure if this fits the sound you described but it might be turbo chatter, where your bov doesnt actually open, the noise you're hearing is the air passing back onto the turbo blades.

Hey you are reading my mind but about four months earlier, If you have played with intercooler and a boost controller on the car you would have noticed that a nipple would be missing on the inlet part of the pipe before the bov that is the vacuum pipe that opens the actuator on the internal waste gate and if you dont have that hooked up you will hit max load causing seveire breakdown at 2k trust me i had the exact problem!!! easy way to fix it is to simply put a T valve in on the blow off valve hose that goes to near the back of the plenum!! that will get rid of your break down at 2k.. P.M if ya want a photo!

made a slight difference but still breaks down, but you can get past the banging and then it tries to pull.. could it be a fuel problem?

but what concerns me is, i gave it a boot full and then went to go into my driveway, stopped and the car stalled, then i started it again and it stalled again but started it and gave it a rev and it idled fine...

its quite farken easy u see...

u get a gapping tool, pick the gap u want, get ur spark plug out, tap them on the ground softly until the gapping ruler u are using fits between the sparking element and the underside of the tip. ur spark plugs come pregapped at 1.1 thats not enough for boost past 6-7psi. that will work, if ur unsure how to do it, go to ur mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...