Jump to content
SAU Community

Y33 Vq30det Turbo To Rb20/25det

MisfitCeffy666
 Share

Recommended Posts

MisfitCeffy666 Rookie

MisfitCeffy666

Posted
Posted

heard a rumor that the vq30det turbo will swap over to Rb20/25det with no problems. im just trying to confirm this because i cant read japanese all that well and cant even really find any info on it. just looking to upgrade for cheap

Link to comment
Share on other sites
666DAN Grand Master

666DAN

Posted
Posted

Funny you should mention that, I've been looking at this engine for some time. From the looks of it yes the turbo will fit (T3 flange) you'll need to get some sort of elbow made up though.

The exhaust housing doesn't look too big, so not sure if it would really be much of a benefit on an RB25, and it will most likely have a nylon compressor wheel if you get a new one from the VQ30DET Neo

Link to comment
Share on other sites
VeX Contributor

VeX

Posted
Posted

Yes the do fit with little modification. you will need to get the inlet pipe for your intercooler streched or get a new pipe as the the VG30 turbo has a 3" outlet compared to the stock skyline one which is 2.5". they are a great upgrade on the RB20 though . But as far as bot up pattern and flange they are identical to the stock.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • niZmO_Man
      RB26 boost leak? limp mode?

      By niZmO_Man · Posted

      Remember our cars are 30+ years old so expect the rubber bits to leak. I'd go around your engine bay with a can of "start ya bastard" or similar and look for leaks. FYI I got my car 10+ years ago with the standard boost restrictor in place, I removed it when I got it and the car never had any issues since (besices a leaking manifold gasket). tl;dr- Look for leaks before proceeding.
    • Dose Pipe Sutututu
      Never ending fuel pump drama

      By Dose Pipe Sutututu · Posted

      That SSR is actually the same (or similar) as the Jaycar 100AMP SSR (which I use). They suggest the resistor to stop the SSR turning on when the ECU turns off (I believe). I personally don't use the resistor as I use the 5V output from the ECU to supply power to the SSR. I do however run a flyback diode, the old Haltech documentation was wrong too and didn't specify the fly back, I mentioned it to a few of their staff and they eventually added it in.
    • elohim_imanu
      Removing sump

      By elohim_imanu · Posted

      I did manage to do this without removing the engine or front cross member, but I had the advantage that the exhaust manifold was removed. I am not setup to support the engine from the top or remove it. 1. Loosen the engine mount nuts so they only have a nut of thread. If it is a manual, I think you have to remove the gearbox to engine support brackets. 2. Jack up the engine off the bottom idler mount. Jack it up till the end of the slot and nut on the mount. You need this clearance to get the pan out at the rear of the engine. 3.Break the sealant seal to sump. I found a oil pan separator tool helpful to get it started. 4. The oil pick up can be removed with the gap available.  5. The oil pan can be removed now. 6. Before assembling, do not apply sealant to the oil pick up area as your hand will rub it all off but apply to the other three and a bit sides. 7. It is a two man job to put the oil pan back, with the sealant, as you do not want it to touch anything and rub off. 8. With one person supporting the oil pan the other can fit the oil pickup 9. Apply the remaining sealant. This would be more difficult with the manifold or turbo in place, but I think it could be done. As you can see my sealant is a bit ugly, but good enough to seal. 10. Lift the sump up to the engine and bolt it on. We found it was easier to use two long guide bolts at each end to get it nice and aligned without touching.
    • MBS206
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By MBS206 · Posted

      I find building an exhaust a really satisfying job! Looks nice!   Did you consider using an oval pipe to get the same cross sectional area but keep it above the chassis rail?
    • Murray_Calavera
      Never ending fuel pump drama

      By Murray_Calavera · Posted

      @Dose Pipe Sutututu Sounds good.  Just double checking with the pull up resistor indicated in haltech's info sheet for their SSR - https://www.haltech.com/product/ht-030202-solid-state-relay-100-amp/  I'm guessing that would only be if the ECU did not have an internal pull up resistor? Their instructions are pretty strongly worded lol "1K pull-up resistor MUST be fitted." 
×
×
  • Create New...