Jump to content
SAU Community

How Does This Happen

tacker

By tacker,
in Engines & Forced Induction

 Share

Recommended Posts

tacker Mentor

tacker

Posted
  • Author
Posted (edited)

yer would you believe i was just sitting at the control light waiting for it to go green to start track session and bang! Engine was only idling thank F#$5.

Radiator got a bit of a touch up from the fan and engine got a bit hot but not to bad would hate to think what would have happened at 8000 rpm?

I put it in and before you say it i have been working on engines for the last 22 years and this is a simple task. Try putting an oil pump or an oil cooling nozzle into a Cummins KTA 50G3 which are both the definition of bloody near impossible.

The pump had already done some track time with no problem then bang

Edited by tacker
STATUS Grand Master

STATUS

Posted
Posted (edited)

Its either an indian cheapy with casting issues (look for flaws, i cant see any in the pic though) or the belts were to tight. I have seen this happen to those copy SR20 sumps getting around small tap on a ripple strip and they literally fall off.

Edited by URAS
tacker Mentor

tacker

Posted
  • Author
Posted (edited)

yer big old smelly, nasty deisels. I am sure belt was not to tight still i guess that would be a reason for this happening but how tight must it have been to break that amount of cast alloy. And would that be possible with 1 little tensioning bolt.

Pump was brand new when i put in on and i put the few kms on it without any issue, so it was never removed from any other engine. Thinking a N1 will now be put on as getting sick of removing cam belt etc to put pump in place only changed the last one as i put new cam belt on and thought i better do the right thing

Edited by tacker
Fanta R33GTR Contributor

Fanta R33GTR

Posted
Posted

The water pump in my GTR did exactly the same thing. The belt was just a little too tight and after a few weeks when I let her rip, it snapped and the pump was held on by only a small piece of metal.

Like other have said,

If it's not that then it's just a cheap pump perhaps with bad manufactering...

taynewguy Community Regular

taynewguy

Posted
Posted

Sounds like you got away with it ok though.

This happened to me a while back in my r33 - threw the fan into the radiator at about 5000rpm.

The fan had a few chunks missing from the blades and the radiator was cactus!

We put it down to a fault/hairline crack in the water pump itself, as the belts were at correct tension.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      Hows your intake piping? Are you still running stock? Having in the stock AFM position would mean, if the BOV was shut/venting out, it'd create the almost stalling kind of effect right // "the rich pulse behaviour" due to MAF thinking air is flowing ? But this would be better than having the bov in the stock position + MAF on/just before cross over piping right?
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • tsuokun
      Lets play a game - What is causing my oil consumption?

      By tsuokun · Posted

      Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
×
×
  • Create New...