Jump to content
SAU Community

Recommended Posts

Here is the Excel file I used to map my Fuel and ignition tables. I am sure some of you guys out there can get some use out of it. I recently had Mick from subzero Dyno my car. You can clearly see the fuel he took out of it at PFC load Value 15-16. The car was being retuned at 1.10bar. The Ignition points around 15-16 need to be trimmed at peak torque to reduce detenation. Did make 225kw tho. When the timing is retarded I think it will negate the extra boost and all I`ll end up with is a slight increase in mid range power only, probably actually loose some up top.

Link to comment
https://www.sau.com.au/forums/topic/16374-power-fc-chart-mapping/
Share on other sites

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

HKS Super Dragger Ex

HKS Dump Pipe

mesh removed from A/F meter (stock r33)

Apexi Air filter /partitioned off

Greddy 28c tube and fin front mount intercooler

Heat wrapped turbo to cat*

*cat in pipe

heat wrapped intake pipe

Power FC

HKS solid twin plate clutch

Cut out front bar

Oil air seperator

Bosch Motorsport fuel pump

Motul 5w40 oil

Nulon G70 with auto trans fluid in the gear box

1bar to 1.10bar boost

HKS EVC4

Pureone oil filter

Stupidly huge fuel filter

BPES7??? plugs 0.7mm

BP ultimate 98 Fuel 1bar- with octane booster for 1.1bar,also another 2degrees added with octane booster.

I`ll modify this post if I can think of any more

Originally posted by Steve

225kw with stock turbo!  1.1bar with stock turbo!!!! you're a very brave man:)

Your right on the money Steve, I only get near those figures with a healthy dose of octane booster and I still get a minor ping. I`m taking it down AIR for the next street meet. Fingers crossed I can get through another 6 passes.

Thanks boostd useful info.

I actually leaned out the fuel map at idle to try and reduce exhaust fumes (I don't have a cat fitted). Hunts a bit now (I took the AFM screens out also), but less likely to gas myself whilst idling in a semi-closed garage.

I'll drop my maps in for the RB26 and post here also.

Anyone else got RB26 maps?

  • 2 weeks later...

Its Greg from base. What do you reckon try loading your figures into my car. Where could I go wrong. Our cars have the same mods virtually. Mine has only had one tune for an hour on a 43degree day. So there is nothing to loose. I am planning a turbo upgrade in the near future so it will have a retune then.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Certainly. It is probably broken under the wire style clamp. At least that one is easier to get at than the front one.   Sounds like it isn't a major leak, I'd start with backing off the the water feed and return banjos into the turbos half a turn then tightening properly. Hardlines can still crack over time, either in the tube (particularly when turbos are changed if the banjo is siezed in the the tube) or at the brazed joins between the lines and the banjo fittings. A coolant system pressure test will reveal all. BTW you'd be able to get a sump without exchange, it will just cost more as they will have to source another stock one for the next customer. If you want to address the sump a much better option is something like this https://www.hioctanedirect.com/hi-octane-racing-sump-extension-nissan-rb26 that you weld in locally (and add the oil return fittings at the same time)
    • Pretty sure you are thinking of the throwout bearing there (which you should change when you change your clutch), when they are worn they will get quieter if you put your foot on the clutch. An input shaft bearing is turning/noisy at all times.
    • I’ll have more of a look into Recaros over the weekend. It’s taken me 2 days to figure out which Bride seats suit my application haha.
    • I am aware of their presence, but the product page looked like that conversion will eliminate the AWD capability. Fact remains it's kind of a hassle to send my oil sump halfway around the world and buying an extra one is expensive and unnecessary. Before I go hat route I'd explore more local options.    Would you recommend I just pull the engine and renew as many things as possible since I'm already having problems with some leaks? Would have to get an engine crane first though.
    • Are there any indicators that the vehicle is in limp mode?  Any dash light, or something.  Or is it just lack of acceleration?
×
×
  • Create New...