Jump to content
SAU Community

Recommended Posts

hey guys

selling these:

BODY:

r32 door mirror's-

r32 2dr drivers door-

r32 2dr passenger door-

r32 REAR reo bar -$130

r32 type-m rear bar -$100

r32 type-m passenger side skirt-$75

r32 shell- 1k

ads23213.jpgbar.jpgreo.jpgside.jpg

DRIVELINE:

r32 gtr/gts4 driveshaft -$150

r32 gtr/gts4 tailshaft - SOLD

A pair of R32 GTR/GTS4 6 bolter rear 31spline 6bolt Axle's - $150

adadadsa2.jpgas33.jpg

SUSPENSION & BRAKES:

R32 GTR front caliper's- offers

r32 type-m rear calipers-offers

full set of r32 GTST M-spec rotors- offers

r32 rear 5 stud hubs with LCA-offers

r32 tein fronts gts4/gtr -

r32 koni rear 2 point height adjustible shocks gts4/gtr-

rear r32 2dr handbrake lines-

wae24ed3.jpgsus.jpgp10retret.jpg sad321.jpg

LIGHTS

r32 type-m fog lights (pair)-

passenger side headlight-$70 ( comes with most of the wiring)

wqe213ads2213.jpgwqewq.jpg

WHEELS

16" 5 stud dishies 8" wide-offers

OTHER

r32 gts4/gtr/gts/gtst ABS unit -offers

interior parts:

r32 2dr rear trim under 1/4 window -$150 both for lhs+rhs

RHS r32 2dr 1/4 window surround- $50 SOLD

rear view mirror-

r32 1993 spec rear seats-$200

r32 gtst steering wheel- ok conditon $100

r32 interior goodies- mostly perfect condition ~take wat u need~ - make an offer

p1010048.jpgp1010045.jpg rearseats2.jpg

let me no

in melb

i might hav sum more so let me no wat u need

Edited by Dan_J
Link to comment
https://www.sau.com.au/forums/topic/164334-delete/
Share on other sites

blinko : think i got it, you mean da left kick panel on da drivers side?

wannabeslida : yea i'll pm da price and price for postage soon

LoNg_ShaNks: no aircon vents only heater vents

ducki: sorri no rad

Edited by Dan_J
Link to comment
https://www.sau.com.au/forums/topic/164334-delete/#findComment-3047497
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...