Jump to content
SAU Community

Recommended Posts

On the good advice of many of the track guys I purchased a Just Jap Racing 19 row external oil cooler for my R33 GTR. Now I needed to get it mounted. It makes sense that you mount it under the front bar / somewhere by the radiator so it gets airflow but precisely where? Does anyone have pics of how they have mounted theirs?

Link to comment
https://www.sau.com.au/forums/topic/164522-where-to-mount-an-oil-cooler/
Share on other sites

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

There's a thread in the diy section that shows one being mounted in behind the indicators on the front bar, I like this idea because it means your not adding extra heat to the airflow through the cooler and radiator. If there isn't enough room there though majority of people mount them between the cooler and the radiator, on the righthand side to keep the lines as short as possiable. Just make up some brackets that bolt to the structure somewhere

I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

Anyway...you will need to take off your bumper and wheel, including wheel arch and make up a set of custom brackets to get it to sit up-right.

Take the panel(Left Front) off a swell, this will help you alot..lol

Your hoses will not be long enough...so you will have to take measurements after you install the cooler.

If you have the relocation kit you will find you will also need a 90 degree bend from the oil cooler...or something of that angle to get a braided oil line to fit.

Good luck....I know I spent an extra $700 to fit the dam thing.....frustrating...

I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

No you were provided the right one.

the R32 one from Trust sits in the front bar passenger side air intake.

the R33 one sits next to the driver's side headlight.

Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

tekin, not quite right mate. greddy make a number of different kits. for 32 GTR alone there is one that mounts in the duct on the passenger side (below the headlight) and one that mounts in front of the radiator and within those two types you can get different size cores. which ever type you order will come with the perfect length lines and brackets and even a little duct. greddy kit is by far and away the best one.

TJ has not bought a greddy unit....but an off the shelf......19Row unit...which can only be installed below the passenger side front lights as I have discussed before.

So he is in need of the items I have listed above..........tj can you keep us informed on what you had to go through to install this unit...

seeing it was not specific to your car.

Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

well it is better, but it shoudln't be a problem. my greddy kit has the cooler mounted down low, but the filter relocater is mounted up high. as long as the pump isn't too worn it will be fine. just keep an eye on pressure that will tell you if there is a problem or not.

Tekin, I was replying to this:

"R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected."

it is wrong. I have a 32 GTR. I have an oil cooler and it is not mounted in front of the radiator. yes you could mount it there but it's a crappy spot to put it as it gets little flow through the core. passenger side duct is the best spot on a 32 GTR and a 33 for that matter.

lol

anywho, whatever is the case, as baron stated one of the best places is in the lower bumper vent on the passenger side, either R33 or R32 gtr.

just remember to cut exhaust holes in the inner guard or bottom stone tray for the air that has passed through the core to escape.

otherwise the cooler will do..... Fark all.

242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

That looks really neat, I might relocate mine and make some deflectors, would work alot better...

Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

Please mate, before you tell others they have 'been corrected', make sure you know what your talking about.

Trust makes various kits, including a 'radiator front' (radiator support mount) kit for BCNR33 and I should know, not because I read it on the internet, but because I have one on my R33 GTR.

I know it's true also. not because I have one, but because I read it. but not on the internet. it was written on the toilet wall of Hobbys International in Shinjuku.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • One other thing worth mentioning when I did this job I only jacked up the driver side as I was only doing work there, but from what I understand both wheels should be in the air when removing the sway bar links?
    • Yep it's an r34. Usually people remove struts without removing the front upper control arm (fuca is what i assume this is?) So not sure why mine wouldn't fit. I know on my other car I did a similar job and it wouldn't fit until I removes the ball joint nut even though I didn't remove it prior.   The upper arm doesn't seem to be in the way (the part that's bolted to the chassis. The part that's bolted onto the j arm I'll check that out though.   I was going to compress the spring and put it in with the compressor attached but not sure if it will work  Haven't seen anyone do it.
    • I have a small lip on the boot of the E90 and I've been toying with the idea of trying to mould it in to the boot to remove the gaps. I guess shaving the seams? No idea what the terminology is here.  What I'm wondering is, if it's current double sided taped down, what would I do to more permanently attach it so it makes a good base for the filler? It only has edges so no way to bolt it down unless I add some braces. I've done a lot of fibre glassing in my time so that's nice and easy but I'm not sure what my options are here.  Sorry, this is the best pic I have and I'm 4 million ks from home ATM.  
    • Based on this comment I went googling. A052's in the sizes I want are certainly not cheap, but I couldn't find anything in the V70A anywhere. How much do they run/where do they get sourced from? From what I know (nothing but internet searches and reviews etc) the R888 has pretty much fallen off from anyone's actual use, and the AO52 is the king of "road legal" rubber. Nobody is driving around on their daily for Z221, AO050, DZ03G. At that point, for purely track only tyres - Why not buy actual slicks? Why does nobody actually do that anyway?
    • This an R34? It shouldn't matter though - it should be the same as on any of the others, and by "any of the others" I mean R32, because that is the car that I have had the front end apart on about 50 times this year. Sometimes, it is much easier to get the lower shock eye onto that pin when: a) you have the upper shock nuts backed off a few turns so you can wiggle it a bit more freely. When they are tight the bottom of the strut is much harder to move that _leeeetle_ bit you might need it to to win the fight. b) you have the outer bolt(s) from the FUCA out and so you can move the lower pin around freely too. Then, all you have to do is put the upper arm back on when you've got the rest back together, and this is where jacking under the balljoint can help.
×
×
  • Create New...