Jump to content
SAU Community

Recommended Posts

On the good advice of many of the track guys I purchased a Just Jap Racing 19 row external oil cooler for my R33 GTR. Now I needed to get it mounted. It makes sense that you mount it under the front bar / somewhere by the radiator so it gets airflow but precisely where? Does anyone have pics of how they have mounted theirs?

Link to comment
https://www.sau.com.au/forums/topic/164522-where-to-mount-an-oil-cooler/
Share on other sites

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

There's a thread in the diy section that shows one being mounted in behind the indicators on the front bar, I like this idea because it means your not adding extra heat to the airflow through the cooler and radiator. If there isn't enough room there though majority of people mount them between the cooler and the radiator, on the righthand side to keep the lines as short as possiable. Just make up some brackets that bolt to the structure somewhere

I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

Anyway...you will need to take off your bumper and wheel, including wheel arch and make up a set of custom brackets to get it to sit up-right.

Take the panel(Left Front) off a swell, this will help you alot..lol

Your hoses will not be long enough...so you will have to take measurements after you install the cooler.

If you have the relocation kit you will find you will also need a 90 degree bend from the oil cooler...or something of that angle to get a braided oil line to fit.

Good luck....I know I spent an extra $700 to fit the dam thing.....frustrating...

I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

No you were provided the right one.

the R32 one from Trust sits in the front bar passenger side air intake.

the R33 one sits next to the driver's side headlight.

Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

tekin, not quite right mate. greddy make a number of different kits. for 32 GTR alone there is one that mounts in the duct on the passenger side (below the headlight) and one that mounts in front of the radiator and within those two types you can get different size cores. which ever type you order will come with the perfect length lines and brackets and even a little duct. greddy kit is by far and away the best one.

TJ has not bought a greddy unit....but an off the shelf......19Row unit...which can only be installed below the passenger side front lights as I have discussed before.

So he is in need of the items I have listed above..........tj can you keep us informed on what you had to go through to install this unit...

seeing it was not specific to your car.

Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

well it is better, but it shoudln't be a problem. my greddy kit has the cooler mounted down low, but the filter relocater is mounted up high. as long as the pump isn't too worn it will be fine. just keep an eye on pressure that will tell you if there is a problem or not.

Tekin, I was replying to this:

"R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected."

it is wrong. I have a 32 GTR. I have an oil cooler and it is not mounted in front of the radiator. yes you could mount it there but it's a crappy spot to put it as it gets little flow through the core. passenger side duct is the best spot on a 32 GTR and a 33 for that matter.

lol

anywho, whatever is the case, as baron stated one of the best places is in the lower bumper vent on the passenger side, either R33 or R32 gtr.

just remember to cut exhaust holes in the inner guard or bottom stone tray for the air that has passed through the core to escape.

otherwise the cooler will do..... Fark all.

242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

That looks really neat, I might relocate mine and make some deflectors, would work alot better...

Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

Please mate, before you tell others they have 'been corrected', make sure you know what your talking about.

Trust makes various kits, including a 'radiator front' (radiator support mount) kit for BCNR33 and I should know, not because I read it on the internet, but because I have one on my R33 GTR.

I know it's true also. not because I have one, but because I read it. but not on the internet. it was written on the toilet wall of Hobbys International in Shinjuku.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Jap premium will be 100 RON. You should use 98.
    • The exhaust gases are at their highest temperature as they leave the exhaust port and enter the manifold. They cool as they flow through the manifold because they transfer heat to the manifold and the manifold loses heat to the surrounding environment. Thus, inevitably, the exhaust gases are cooler as they enter the turbo compared to when they entered the exhaust manifold. So, yes, the exhaust manifold can easily get as hot as the turbine housing. Having said that, you will generally see the highest temperatures where the exhaust gases have to slow down or they are concentrated into one area - which is usually the collector on the manifold and in the turbine housing, because the gases slam into the metal at those places, increasing the convective heat transfer coefficient and transferring even more heat to the metal than they might just flowing past elsewhere. Exhaust manifold heat shields are a good idea - certainly for the stock manifold they are there from the factory. People seldom have anything like that on a tubular manifold because they are hard to achieve. Some might wrap a tube manifold with fibreglass tape - but this has a reputation of leading to cracked welds. The best case is generally to put ceramic coating onto the manifold to prevent it getting as hot (internal coating) and radiating/convecting heat into the bay (external coating). All the real heat from a turbo comes from the exhaust side. The gases entering are at ~800-900°C and the steel/iron gets nearly that hot. The compressor side is only going to heat the charge air up to <<200°C (typically not much more than 100°C). So that's nothing, by comparison. The compressor is not a significant source of engine bay heat.
    • Late to the party, specifically joined this forum as I just bought one of these and this thread has been a gold mine of info. If the OP is still around, mind if I ask what gas you been putting in yours? Mine has a Japanese sticker in the cap saying premium but it seems to get way worse mileage on premium (95) than 91. I always thought it was meant to be the other way round🤷 I do think Nissans claimed "6l/100km" is a bit fantastical 😂
    • Does exhaust manifold get hot as turno exhuast side? I have a turbo cover to managr heat in the engine bay but  nothing is covering the exhaust manifold before turbo   i know as turbo does compress air, the temp does go up however does that mean exhaust manifold would be as hot?
    • It's excellent but I'm still breaking it in so I'm not 100% sure where it'll end up. I would say it's about 15% heavier than stock and the smoothness of the slip zone is quite progressive but you need to be a little patient compared to stock or it'll bite hard and stall. Stock I got away with absolutely horrid clutch control. Like I said before I couldn't even tell where the clutch would grab when it was stock so releasing way too quickly without enough revs it would just slip and the revs would drop lower than ideal but that would be the end of it. Currently there's a bit of a nasty clutch judder if I don't apply enough revs + find the exact wrong point of the slip point in the clutch pedal but it feels like it's slowly resolving as I drive it more. I would not recommend the competition clutch unless you really need the extra clamp force. I think this clutch combined with the Nismo operating cylinder is going to be exactly what I want. Enough bite that you need to remember the release point to avoid stalling or rough shifts, but progressive enough that it's not hard to drive by any means and not heavy at all. I tried a "super single" clutch on my friend's 997.2 Turbo 6MT and that was absolutely horrid. It runs an electrohydraulic power steering pump for the clutch power boost so there's zero feedback in the clutch pedal and there was a horrific clutch shudder well after break-in due to the lack of marcel springs or hub springs in the friction disk. It felt like the slip zone was the thickness of a single toe twitch as well so it was almost impossible to avoid stalling it unless you gave it a ton of revs and just dumped the clutch instead of trying to be smooth with it. I was terrified of pulling out in front of traffic. I have also tried some kind of "super single" on an EK9 and that makes this twin plate Coppermix look like a stock clutch. Releasing the clutch pedal even slightly too quickly feels like you're getting rear-ended. The pedal is extremely heavy as well and there's no vacuum assist like the GTR.
×
×
  • Create New...