Jump to content
SAU Community

Recommended Posts

Ok, i figured other forums i frequent have them as well

please post as many specs of your wheels as possible

width and offsets being the MOST important

Picture from the side straight on, and one from the front straight on (to see if they stick out, or sink in for fitment wise)

ill start

Stock M35 wheels.

15mm spacers front and rear to clear GTR brakes

225/50/17 tires

17x7 id imagine is waht it looks like

383528502_13d43d07ff.jpg

383528569_5856cb5a76.jpg

Work euroline

18x9 -5

18x0 +20

235/40/18

400501903_42836c68bd.jpg

400501941_265dd452bc.jpg

400501811_a1f0a65d3f.jpg

above is with stock fenders

below is with midified fenders

406702878_99e1df16bd.jpg

406702791_5d46ba756f.jpg

Work Emotion XD9

18x9 +20 all around +20mm spacer on the front

225/40/18

453749229_cabaf516a7.jpg

453749179_9735cbd03b.jpg

please contribute

Link to comment
https://www.sau.com.au/forums/topic/164936-post-your-wheelstire-size-and-specs/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

17 x 9 - Standard R33GTR wheels with 245/40/17's

Pictures are at 340 mm front and 330 mm rear, which was too low. It's now at 355 mm front and 350 mm rear, much better ride and handling.

R33GTR_Wheels_340mm_Side.jpg

R33GTR_Wheels_340mm_along.jpg

:D cheers :(

  • 4 weeks later...

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

  yokotas13 said:
18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

Your using 235's on 10 inch rims as per per your first post?

They would look mega stretched?

A "normal" person would use a smaller width rim and run the correct width tyre for comfort, looks, handling and safety

am i normal?

I use a 225/40 on a 9 inch wide and a 235/40 on a 10 inch wide

its about clearance, the stretch in the sidewall allows you to run a wider/lower offset without fear of rubbing so when the camber changes in a turn, it acts like a circle and not a square like a normal tire

  yokotas13 said:
am i normal?

NO :thumbsup:

That's why you should explain or clairfy when posting esp when people are asking a question about a topic they do not know anything about. Otherwise someone is going go and buy a set of wheels too wide or the wrong offset and have to beat the shit out of the rear guards and run a way too narrow a tyre for the rim size.

  yokotas13 said:
18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

cool...thanks grant.

mate has a set of eurolines ..18*9 and 18*10 ..both with +35 offset...i'll try them for fit this weekend....oh and tyres are 235 at the rear too...really stretchhhhhed

Running Advanti Racing 'Karla" wheels:

Wheels: 19x8 +35

Tyres: 245/35 R19 Hankook K104

They are being replaced (due to a fault) with Enkei RP03 model which should fill the guards a little more, I think.

post-17581-1179964171_thumb.jpg

post-17581-1179964287_thumb.jpg

  darrinspencer said:
R34 GTR 18x9 +30

245/40/18 or could be 245/35/18

aaaaaastageart093bn2.jpg

My car looks like these 2 once the front gets painted. Mine is silver

that looks amazing :thumbsup::D

Edited by Brycey

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...