Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

The garret int gate (gt30-gt35) housings suffer a tad boost creep. The balancing of dump and wastegate pipe size is what makes or breaks a setup. An open mouth dump with these turbo's = boost creep, anything less than a 2" wastegate pipe when paired with a 3" dump = boost creep. Then there's the enlarging of wastegate flap size which does work well but requires a strong wastegate spring to prevent the flap being blown open due to back pressure within the scroll.

The HKS ProS housings run a large flap that does get blown open even with stiff actuators.

Rework the dump pipe, reduce the size of the wastegate pipe. Make it harder for the exhaust gas to flow out of that wastegate.

I've never seen it done but there's no reason why it wouldn't work it works int he opposite circumstance - boost creep.

Kinda off topic I know, but what was your MPH with those runs? Just wondering, as I'd expect 265rwkw to be around the 115mph mark?

113 mph - the best run was with track temps in high 40's, 35 degree day of all things. There is definately is more in it in tuning and boost level/control wise but I'm a bit sceptical on the bottom end holding up - I hate listening to them on a dyno pull.

Currently it's only got the 15 psi wastegate spring - even though it's a 15 psi spring as you start to make boost even 10 psi the wastegate feed will be weakening the spring tension allowing the wategate to blow open eventually. That's why a bleed style boost control and a 20 psi spring should make a difference.

Cheers

270rkw, hi-flow and the supporting mods...suspension blah blah

18psi @ just a tad over 3000rpm and holds stong to redline. Who is gonna complain about that.

btw 15psi and 18psi much f**k all difference with a high flow in terms of power....however watch ur mid range torque go through the roof.

The garret int gate (gt30-gt35) housings suffer a tad boost creep. The balancing of dump and wastegate pipe size is what makes or breaks a setup. An open mouth dump with these turbo's = boost creep, anything less than a 2" wastegate pipe when paired with a 3" dump = boost creep. Then there's the enlarging of wastegate flap size which does work well but requires a strong wastegate spring to prevent the flap being blown open due to back pressure within the scroll.

The HKS ProS housings run a large flap that does get blown open even with stiff actuators.

Rework the dump pipe, reduce the size of the wastegate pipe. Make it harder for the exhaust gas to flow out of that wastegate.

I've never seen it done but there's no reason why it wouldn't work it works int he opposite circumstance - boost creep.

Makes sense but I'd hate to re-work this! I'll try a few other things first.

Cheers

post-12959-1177239074.jpg

Edited by gtst25

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...