Jump to content
SAU Community

Finally Got Slo-o31 R31 To The Track

S3_Girl

By S3_Girl,
in South Australia

 Share

Recommended Posts

S3_Girl Enthusiast

S3_Girl

Posted
Posted

Finally got to the drags this weekend, unfortunately it didn't go all to plan,

the car had a massive boost leak, first run on 19psi(with the boost controller set to 26psi)

the car went 10.67 at 132.94 with a 1.77 60 ft, we coudn't fix the boost leak so turned up the boost controller

to 25psi manually(so the turbo was probally pumping out around 35psi to make 25 in the motor), then the

transbrake woudn't work. So i stalled it on the brake pedal, rolled out for a 1.68 60 ft and ran 10.21 at

140.9mph, all on pump fuel/ full exhaust and at least 20rwkw less than i usually drive it on the street with.

Car didn't use a full slick either , just a m/t street grooved slick that i have been driving round on.

So CTIFLY record has FINALLY been broken.

There a lot more left in this combo, if the transbrake worked it would have gone 9 something on that pass

and theres another 50rwkw left in the tune on pump fuel and 26psi still, unfortunately the stcck bottom end

finally went bang..the alternator failed and the voltage dropped to 7volts, killing the fuel pumps

and altering the injector pulse width....time for a decent forged motor

cheers

darren

video -

chops Experienced

chops

Posted
Posted

Hopefully you got some better traction there on the Sunday after two days of rubber being laid.

Heaps of traction problems for the serious cars there this weekend.

That thing is a weapon, and it's only a matter of time for the 9.

If we'd known you were going to be there racing, Nightcrawler and myself might have hung around to see you run.

There WAS a 9 run there by a blue skyline that weekend though...

S3_Girl Enthusiast

S3_Girl

Posted
  • Author
Posted

cross ply et street, i haven't much faith in the radials, as my set for the street in 17's are

are joke and they wear quicker, 4 nights with just roll ons, no wheelies and they were bald,

not good value at $640.

The block/rods etc are all fine, sounds like i broke a ringland on one piston, still starts first go and drives,

just not on all cylinders:)"

cheers

darren

Cubes Grand Master

Cubes

Posted
Posted
just a shame you couldnt catch the cressida!

and his engine is still running strong...

just stirring...

good effort.

lol yep Jays running on a fresh motor.. Already done one in. :closedeyes:

What times did Jay run? Jake was out there also?

The block/rods etc are all fine, sounds like i broke a ringland on one piston, still starts first go and drives,

just not on all cylinders:)"

Obviously detonation killed the piston. A bastard the alternator let go. :)

All in street trim, daily tyres etc.. Top work Darren.

dangerman4 Mentor

dangerman4

Posted
Posted
lol yep Jays running on a fresh motor.. Already done one in. :P

What times did Jay run? Jake was out there also?

Obviously detonation killed the piston. A bastard the alternator let go. :(

All in street trim, daily tyres etc.. Top work Darren.

10.1 at 143mph

Jays "fresh" motor is still just a stock bottom end.

it goes to show that both nissan and toyota 3ltr bottom ends can pull some good numbers

Cubes Grand Master

Cubes

Posted
Posted
10.1 at 143mph

Jays "fresh" motor is still just a stock bottom end.

it goes to show that both nissan and toyota 3ltr bottom ends can pull some good numbers

lol yes.. I believe his origional motor let go due to a fuel pump/lean out issue also. :P

But definitely tough as bottom ends.

Jay run on slicks or similiar tyres to Darren? Great effort from the 5speed.

andz Mentor

andz

Posted
Posted
Finally got to the drags this weekend, unfortunately it didn't go all to plan,

the car had a massive boost leak, first run on 19psi(with the boost controller set to 26psi)

the car went 10.67 at 132.94 with a 1.77 60 ft, we coudn't fix the boost leak so turned up the boost controller

to 25psi manually(so the turbo was probally pumping out around 35psi to make 25 in the motor), then the

transbrake woudn't work. So i stalled it on the brake pedal, rolled out for a 1.68 60 ft and ran 10.21 at

140.9mph, all on pump fuel/ full exhaust and at least 20rwkw less than i usually drive it on the street with.

Car didn't use a full slick either , just a m/t street grooved slick that i have been driving round on.

So CTIFLY record has FINALLY been broken.

There a lot more left in this combo, if the transbrake worked it would have gone 9 something on that pass

and theres another 50rwkw left in the tune on pump fuel and 26psi still, unfortunately the stcck bottom end

finally went bang..the alternator failed and the voltage dropped to 7volts, killing the fuel pumps

and altering the injector pulse width....time for a decent forged motor

cheers

darren

video -

btw...where's thedrag strip? is it in adl? open to public?

i thought adl only has AIR

10sec car :)

S3_Girl Enthusiast

S3_Girl

Posted
  • Author
Posted
lol yes.. I believe his origional motor let go due to a fuel pump/lean out issue also. :)

But definitely tough as bottom ends.

Jay run on slicks or similiar tyres to Darren? Great effort from the 5speed.

jay ran on full slicks, race fuel, no exhaust, bloody good time for a manual!!,

i think they are going back for 9's soon.

jake went 10.3 at 136mph with one pass then blew the trans, that will be easily in the 9's

in a couple of weeks aswell!

I personally have no interest in race fuels,no exhaust etc, i want to know how fast my car runs how i always

drive/drove it, and it makes it interesting,anyone can tune a car on race fuel, it's full proof, wind the compressor till

it noses over, set timing for peak torque, walla, no balancing act.

the car would easily go upper 140mph traps with those mods and well into the 9's setup

I had 1 pass on fullboost, if the motor lasted it would have pissed in a better time..but shit happens:)

next time:)

cheers

darren

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      Hello Everyone

      By luke gtr · Posted

      Actually,  just remembered there should be info in the threads (somewhere) about swapping to a manual steering rack and deleting power steering all together. 
    • 180 wanabe
      Thinking of getting a Q50 300hp and just tuning it instead of getting the Q50 Red or 400R

      By 180 wanabe · Posted

      Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • joshuaho96
      R34 power steering

      By joshuaho96 · Posted

      Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • Kinks
      Skid pans in/around Sydney?

      By Kinks · Posted

      I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
×
×
  • Create New...