Jump to content
SAU Community

Recommended Posts

I have done a bit of searching and found that all the rebuilds done on an rb26 are to beaf them up. What I want to know is what is invloved in rebuilding a standrad r33 gtr motor back to standard form. And roughly how much it would cost. Including labour and excluding labour. Has any one rebuilt their gtr back to standard.

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/
Share on other sites

  • 2 months later...

As of 26/06/07 I have had the engine pulled apart. Found that piston 6 was missing a section so I decided to have it rebuilt. I was wanting to rebuild it back to the standard specification but this did not seem feasable as standard gtr pistons from nissan are over $2000. So I went with a set of oversized forged JE pistons. The motor is currently being rebuilt and will hopefully be finished by the end of the week.

Total known costs to date:

-Pistons , $1660 with rings inc

-Labour to have block pulled apart, honning of all bores and pistons attached to original conrods and a gasket kit, $1000

-Engine removal $unknown

-Engine reinstatement $unknown

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3198630
Share on other sites

I'd budget around 7-8k safe, the gasket kit, headgasket, pistons, bearings, block and head work plus labour will pull upto to that easy, not to mention a clutch or ecu ..

I did the works on my gtr cost near 15k...

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3198877
Share on other sites

you are better off selling your engine to someone who wants to build a motor and buy a second hand job.

rb26's are depressingly expensive... if you do one thing u may as well do another and another and another and eventually you will be $20k out of pocket

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3201036
Share on other sites

you are better off selling your engine to someone who wants to build a motor and buy a second hand job.

rb26's are depressingly expensive... if you do one thing u may as well do another and another and another and eventually you will be $20k out of pocket

Amen to that - open your wallet, bend over and just take it like a pedophile in a jail shower!!!

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3201176
Share on other sites

  • 2 months later...

Ok, as of 02/09/2007.........

Total Rebuild with forged pistons came to $6040.77

Break down of price

Engine reconditioning works: $1012.60, what was conducted is as follows.

-Degrease & hot tank long motor

-Engine block bore & hone

-Surface grind head

-Measure & linish crank shaft

-Dismantle, check tunnels, check conrods, crank & pistons

-Vacum test, dismantle & inspect cylinder head

-Bleed down hydraulic, fit valve stem seal

-Supply main bearings

-Supply conrod bearings

Misc. Parts.

-Set of JE Forged pistons rings inc. $1660

-Full gasket rebuild kit $358.84

Dismantle & Reassemble engine(Incl assembly of head) $799

4 Liters of running in engine oil $32.65

2.5 Liters of Diff oil $20.68

6 Platinum spark plugs $108

Engine timing belt $109

52 Hours labor to remove head and engine, reinstate $1960

engine after it was rebuilt, road test, bed in new rings

& service

I also replaced the gear box oil with the redline light weight $152.47

shock proof gear oil but that is not included in the total

rebuild figure

I have done a little over 2000km since the rebuild and am happy to report that the engine is running well & better than ever. I will be taking the car to AVO Turboworld in Melbourne in the middle of this month to have a final check over on a dyno, as well as a power run.

FYI, What actually happened was I noticed that when the engine was cold it would miss a little but when it warmed up it would come good. Except one day it didnt come good. So I had someone look at it and we found that cylinder 6 was compressing at about 49KPa(I think it was measured in kilo pascals), compared to the usual 160KPa(I think) from the remaining 5, so we pulled the head off and found that a big chunk of the piston was gone from piston 6. Later when pulled apart it was found that piston 5 had a hair line fracture. The engine was then rebuilt.

Most importantly, We arent sure why it happened or where the pieces of the piton went as on inspecting both turbos, they had suffered no damage.

Another point I will make is that this GTR is not very modified.....at all.

List of mods.

-Cat back titanium Fijutsubo Giken Exhaust and now JE oversized forged pistons-Only mechanical mods

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3323584
Share on other sites

Yeah, standard turbo's went back on, but its still running standard boost and will stay that way. For now I'm enjoying the standard car, despite the slight increase in displacement. If it was feasable a set of standard pistons would have went in.

I also forgot to mention it has 2 Blitz blowoff valves, but there not really much of a mod these days.

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3323895
Share on other sites

$6K for an RB26 rebuild with forged pistons..

got to be the lowest cost so far.

I'd be real worried about those turbo's now..

main problem with RB26 rebuilds though isn't it..

even if you were to put a set of hiflows on there, the cost to purchase and have them installed would be about $2K surely.

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3324500
Share on other sites

I'm new at this but is there supposed to be something wrong with my turbos because they have been inspected and there is nothing wrong with them. Everything that needed to be replaced, was.

Tell me this, what was I going to say when selling them. "here's two Garret T28's of an R33 GTR for sale. In excellent condition with no shaft play, impeller blades all in good condition. Reason for selling: They were left over parts when I rebuilt the engine"

Can anyone please tell me why they need to be replaced. More importantly can anyone tell me why a stock version of one of the most alleged bulletproof and reliable motors built by Nissan managed to chew up piston 6

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3325083
Share on other sites

detonation will kill any engine in time

hows your fuel pump after 10 years?

are your injectors flowing the same after 10 years?

changed your fuel filter recently?

what fuel were/are you putting in the thing?

it might have been on the edge when it left japan. whos knows what kinda life it had before

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3325384
Share on other sites

standard turbos and valve guides still???

6k twice isnt going to end up looking cheap

If the turbos let go ( they have a habbit of letting go when removed and replaced) it will be a lot more that $6k

Looks like they used the old oil pump as well, next time they will have to change that tooand a lot of other stuff that will have ceramic dust through it.

Link to comment
https://www.sau.com.au/forums/topic/165362-rb26-rebuild/#findComment-3325708
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...