Jump to content
SAU Community

Recommended Posts

echo x 11ty dickhead comments.

You must have got the 1 in 4 kellogs box in which you get a free licence.

I say, invest in KY Lube as you are going to be...well....rammed hard for many years.

  • Replies 141
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

mate, it's been said before, but i'll say it again. You're 19, and this is number 4. Exceeding the speed limit by over 100km/h, you're going to get f*cked on and f*cked on bigtime. If the judge likes you, you won't get thrown in the slammer, but it is a possibility. That's my guess anyway. But you won't be driving for a good few years atleast, and your car will more than likely be impounded.

What exactly were the previous offences? If they're basically the same of this, then, well, yea.

I might go eat my noodles now.

considering these were the following threads that you started:

http://www.skylinesaustralia.com/forums/in...p;#entry1552286

and

<a href="http://www.skylinesaustralia.com/forums/index.php?showtopic=82374&st=0&p=1493069&#entry1493069" target="_blank">

http://www.skylinesaustralia.com/forums/in...p;#entry1493069</a>

it seems that you havent learnt the lesson at all. We all have done stupid things - but this is your FOURTH time??? damn man.....please - if for some strange reason they let you off easy with just a slap on the wrist - buy my 1982 honda civic and drive that till you are 40. It can only hit 100 km/h and is perfect for jsut commuting.

Seriously man, what were you thinking??????? I doubt you will be let off. if it is the 4th time, with all the prior convictions, it looks like jail time to me - unless your lawyer can say something unreal to save your sorry ass. (e.g poor mental health, or something like that)

Good luck is all I can say.

edit: i sure hope this is a story that you made up.......

Edited by emsta2003

how is it possible to loose it 4 times ? thats a big amount .. agreed with everything that every one has said . so you have been driving for roughly 2 years , and been caught 4 times , thats CRAZY ,

i lost my license 4.5 months ago .... racing - it was the best thing that has ever happened to me . taught me a valuable lesson . ill never be speeding again . i know how hard it is with out a car . its a privilege to have a license , most of us take advantage of that

i got caught doing 143 in a 60 zone . i could of attempted to get away , as they were on the otherside of the road . but im glad i didnt - other wise i would never have learnt this lesson the hard way! plus if your caught the punishment is much worse ..

What's a solicitor going to do??? Try to prove he wasn't speeding??? If he was dragging someone he's gone, no one in the world (EVEN the judge) can do anything about it, he broke the law for no reason, and they will get him.

Edited by pablo101

Man, good luck. Youre really gonna need it.

And yeah, wouldnt be surprised if you get locked up for a little while over something as serious as this with so many prior convictions in such a short timeframe.

Only lost my license once, for speeding previously, for 6 months.

Are you all serious about Jail Time?

Dude, think about it, you've been done heaps of times, check out the RTA site about serious driving offences

It might be a possiblity

But Good Luck!

I can't believe you're allowed to have a license, and I sure hope you're permanently suspended from driving for this.

Your best legal advice is to sell the car and start walking everywhere now, cos you'll be doing plenty of it for a long, long time...

Are you all serious about Jail Time?

didnt you say in the other thread that you lost it for 12 months?

http://www.skylinesaustralia.com/forums/in...c=82374&hl=

the way they would see it is....

Police: "hmmm...young habibskyline has had 4 prior convictions...hmmmm....if we dont give him a jail term, sonny jim here wont learn a lesson. Lets put him in jail so that he does not kill himself or anyone else"

Judge: "ditto"

thats how easy it will be for them to consider jail for u man

Furious driving; Reckless driving; Driving in a manner or at a speed dangerous Maximum court-imposed fine $2,200 $3,300

Maximum gaol term 9 months 12 months

Disqualification - minimum 12 months 2 years

Disqualification - maximum Unlimited Unlimited

Disqualification - in the absence of a specific court order 3 years 5 years

Does that answer your question?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...