Jump to content
SAU Community

Recommended Posts

Thanks guys, but dont I need to remove the existing paint etc before I paint? I dont have the necessary skills/equipment for that :P

last time i paint my front, didnt bother removing all the paint, just sand prob the top coat and make it smooth..

paint still good till now..

you dont need any skills to sand something..and only need some sand paper..

last time i paint my front, didnt bother removing all the paint, just sand prob the top coat and make it smooth..

paint still good till now..

you dont need any skills to sand something..and only need some sand paper..

What about the oven etc for the paint? Or painting the plastic is not that hard?

hey

i sorta work 4 a custom spraypainting garage n ull need to sand the bar with 800 grade sand paper till theres no shine AT ALL!

if u dont then theres a good chance the paint will flake off later on.

u wont need to prime it so long as theres no major dints or scratches (depends how nice u want it to look)

if u get it 2 that stage i think ull b suprised how cheap places will paint a bar thats all ready prepared.

remember paint fades over time so just looking the colour code up on the net might not do, u might hav 2 adjust the colour 2 match. thats tricky.

good luck with it

800 is too smooth for spraying with paint, shouldnt be smoother than 400 grit - this allows some texture for the paint to stick to. If you sand to 800 or 1200 then spray paint, eventually you'll get a small stone chip and a large flake of paint will drop off. I've just finished spraying one of my cars, and had pleanty of advice from my paint supplier!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How's your first born doing? 😛 As for now what? Time to forget about it for 12 to 18 months while your go down a totally unrelated rabbit hole... 😛
    • Fuse taps are perfectly fine to use, especially when you're adding stuff for your own car, and so long as you're being smart about it. IE, don't throw a 30amp circuit, onto a circuit that is only a small circuit. It's best to add a small circuit, to one that is already quite large. Oh, and make sure you're not going to blow the fuses that are further upstream too! I dislike their use in other applications, such as alarms, telematics/tracking devices etc, as it's far too easy for someone to unplug them and render a system useless. Those sorts of devices I go for wiring in quite secretively.
    • Fob is all cleaned up and it’s working well!! The amount of Vegemite looking sh*t that was in there is mind blowing 
    • Given it is temporary, I bought a  cheapy gauge mount (which has become enflattened) which I will screw into the existing phone mount Also a first for me; given this is a temporary install I could not think of any reason not to use one of those "add a fuse" thingies to source the battery and IGN power. I had always figured they were pretty dodgy but having a good look at them I think they are a valid option for sourcing power from an existing source without cutting 
    • Finally for now, a bit more work on the transmission temp gauge. I was wondering how Raceworks do a gauge for $100 that autometer want $500 for. No idea about the accuracy of course, but they have cut a few corners that made things hard.  First one I mentioned above, the sender is physically difficult to fit and doesn't work with their own adapters (the extra fittings I used to get the sender into a hose cost more than the whole gauge, lucky I had stuff in the shed) Second, the temp sender wires are way too short. They are shown as 2.7m on the box and I know my routing was long from navigator headlight to driver's firewall back to centre console, but I had to lengthen them by about 2m total - 2 joins in each wire. Also, same with the supplied power loom, they needed about an extra 1m to get the fuse box where I sourced power. Another join in each wire since one end wasn't supplied terminated. I know they could argue that the wires might be long enough depending on situation, but when you consider parts and particularly labour, it would be a very expensive cheap gauge if you can't do the work yourself. And, only a small issue....but it would have been nice if they remembered to tap a tread onto *both* spacers they supplied for the bracket....I haven't had to use the M4 tap often!
×
×
  • Create New...