Jump to content
SAU Community

Recommended Posts

hey, im curious as to what size speakers people have put into their r33's. ive been told that only 6" is all that fits. and by others that 6.5" and 7" fits perfect. ive found some 6.5" splits for the front that i like. but want to know for sure if they'll fit or not first. also what fits in the parcel tray. thanks people!

Link to comment
https://www.sau.com.au/forums/topic/165893-r33-s1-speaker-question/
Share on other sites

hey man

i think 6.5" splits will fit in the front. well im guessing they would!!

but in the rear i think you'll have to go with some 6x9's!

but don't take my word for it, could very easily be wrong!! ;)

i got 6" in the front, they fit perfect, cant see why u cant put 6.5" in with little modificatin.

in the back i got 6x9's but i need spacers. i then recarpeted the shelf and make it look like its a moulded parcel. will get pics of shelf if u want but inregards to front shouldn't be a prob.

hey man

i think 6.5" splits will fit in the front. well im guessing they would!!

but in the rear i think you'll have to go with some 6x9's!

but don't take my word for it, could very easily be wrong!! ;)

6" (6.25 on stock mounts) front - 6.75 rear. with custom mounts anything is possible. 6x9s - no no without a LOT of work.

  • 2 weeks later...
6.5" will fit if you make an MDF ring to sit them on.

6x9s in parcel shelf are easy. did them last week for -R33GTS- All you need is spacers and they sit perfectly.

So you need a MDF spacer to pull the speaker away a bit, is that so it fits in the hole - or so the back of the speaker doesnt hit the inside of the door?

I'm thinking this is what fhrx did here:

8.jpg

yep.

when i did R33GTS's spacers i made a template so i can just make them when ever i need to without having to measure up again. pretty much the same as Fhrx's. i used 6mm MDF and i had no worries.

for the 6x9 spacers, he already had a set in, but 16mm spacers would work a treat if u were to buy pre made ones.

only things with the ones FHRX show is this. pull your door off, note where the tab is on the back. that is the door pocket seal. with the ones pictured that block is gone and anything in the door pocket goes straight into the door. I usually make an exact copy of them that way you dont loose things.

  • 4 weeks later...
yep.

when i did R33GTS's spacers i made a template so i can just make them when ever i need to without having to measure up again. pretty much the same as Fhrx's. i used 6mm MDF and i had no worries.

for the 6x9 spacers, he already had a set in, but 16mm spacers would work a treat if u were to buy pre made ones.

hi mate can u tell me where i can get some spacers off the internet for my 6x9s to go in my rear shelf r33series1gtst

thx ray

im probably going out to buy a set of 6" to fit in the front + rear on the weekend and will be running off an amp. Anyone know if Alpine do a 6" speaker? Would preferably like to go with Alpine but all i can find is 6.5"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Some of them keep working fine. 9 out of 10 of them end up causing an absolute misery bleeding the system and get thrown on the workshop floor in a tantrum and never thought about again because they were never really needed and just added crap to the car that we could have done without. Same-same with HICAS, A-LSD, and various other stupidities that over eager 10x engineers thought we had to have.
    • Not required but appreciated. Super Coppermix Twin even the non-competition model feels like the pedal is noticeably heavier than stock which was pretty well judged IMO. I'll be swapping in the Nismo operating cylinder soon to see how that feels.  Personally I haven't felt anything that justifies replacing the damping loop, at least compared to more modern stuff where the clutch delay valve is actually quite noticeable.
    • He made that comment in my thread - In my case the vents ARE to lower engine heat, when the car is not moving, which is the only scenario I have heat problems with the aircon on, sitting in traffic, on 40C+ days. I can't imagine a scenario that this NC needs any at this point in time. I do not know if it will actually make my cooling when the car is MOVING worse, and I sincerely hope that won't be the case. If it does, well, um, f**k.
    • Nice, thanks. Thats why I was asking, there'd been a fair bit of discussion in the E90 world about vents and where it makes sense to put one (ie, over the filters is not great as that is inline or slightly behind the struts and in higher pressure area). I struggle with air flow and pressures. It sill weirds me out that a radiator in the boot can work. 
    • Neither really Vents, when located in the right place, will lower the engine bay "pressure", as air has a path to escape, thus lowering the engine bay pressure, thus.....improving the efficiency on the coolant stack (read: IC, condenser, radiator) This is why the Blits vented bonnet on my 33 worked so well, the vent was in the front 1/3 of the bonnet, which put it right after the radiator  If the vents are to far back toward the windscreen, which is a high pressure zone, it can actually force air into the engine bay, causing higher pressure and effectively loosing efficiency on the cooling stack, like the fab of raising the rear of the bonnet, which does allow heat to escape, but only when the car isn't moving  There's heaps of cool "fluid dynamics" info out there, but, I'll attach a video of a 'Merican joint that focuses on "Miatas" as I found it when looking into vents for mine, they explain it way better than me  
×
×
  • Create New...