Jump to content
SAU Community

Recommended Posts

I noticed a weird smell in the car, so i started sniffing around. Lifted the drivers side floor mat, and found the carpet under it is damp.

No other area of the carpet seems wet. just a patch about 30cm x 30cm, where your left heel would rest.

I cant see where the water got in. The car was sitting out overnight in heavy rain 2 days ago.

Its just water as far as i can tell, not coolant or anything else.

Any ideas? Anyone had this issue?

Its an s1 R33.

Link to comment
https://www.sau.com.au/forums/topic/165899-drivers-side-carpet-is-wet/
Share on other sites

its probably getting in from the outside... LOL!

i dunno, sounds weird... hopefully it wasnt dripping from above... check under the car next chance you get... that or it could be getting through the firewall, and dripping into the inside... try and follow any signs of water if you can, otherwise, check your firewalls for holes and missing gromets...

my 2c

the outside hey? ;)

i'm thinking it might be getting in from underneath. i'll have the car on a hoist this week, so i'll have a good look.

i looked for water marks on the inside of the firewall, behind the pedals etc, but found none. in fact, theres dust on there.

Yeah that rules out either a leaking heater core or overflowing evaporater drip tray. Only really leaves water coming in from outside, and seeing you said it was in the rain for 2 days it sounds like its the most logical answer. Its probably water leaking in from the area just in front of the dash where the interior air intake is. Water could be trapped in there and leaking inside the car. Either that or maybe windscreen seal?

whenever i wash my car (r33 aswell) small splashes of water get in between the door window and the b-pillar if i spray in the wrong direction, maybe it was similar to this :X

My car still smells like that generic imported car smell...

My Commodore developed this problem some time back.. it was the water-runoff kinda holes where your windscreen meets your firewall. I forget what my Skyline looks like around that area, but the Commy had holes with mesh into the front quarter panels for the water to drain out. Problem is, the water just drains straight out onto the firewall part, which is usually not painted... just primed (on the inside of the quarter panel and inside of the firewall... the engine-bay side is painted). So it rusted a little hole through, then the water just slid down the inside of the firewall, under the carpet, and pooled on the passenger side floor.

I couldn't find any water anywhere but on the floor, and the top of the carpet was dry. Did my head in until I stripped back the carpet for a week in heavy rain.

If you can't see where it's coming from, i'm still betting on gravity, and would suggest that it's coming from ABOVE, and checking under the car might not be the answer. =-]

I could be very wrong, but I doubt the floorpan has rusted away.

Edited by RANDY

ok, i found the leak.

it turned out to be a large gromit that feeds a bunch of wiring into the cabin.

the water that collects inside the vents under the wipers, overuns onto the firewall (engine bay side) and was geting in thru this gromit that had popped out of its place. you cant quite see it in the pic, but it's where the arrow is pointing.

post-29392-1177496503.jpg

in my case i had my boost line running thru here, so i cut a hole into the grommit and ran the line thru, and used sikaflex to seal around the line.

will test it again tomoro when its all dry and set.

  • 1 year later...

i have the same problem at the moment, the picture doesnt work anymore, but do you need to remove the plastic mesh cover under the wipers?, or just check the gromets on the firewall in the engine bay where the wiring passes through the firewall into the cabin?

  • 1 month later...

fark, i feel like a horrible person. took me months to reply, and its probably far too late now :domokun:

no need to remove anything external. just clear the way so you can see the firerwall clearly up and to the right of the accellerator. it was right up there. my neck got sore trying to see it. in my case it was a large grommit that i think feeds the bonnet release cable into the car.

fark, i feel like a horrible person. took me months to reply, and its probably far too late now :)

no need to remove anything external. just clear the way so you can see the firerwall clearly up and to the right of the accellerator. it was right up there. my neck got sore trying to see it. in my case it was a large grommit that i think feeds the bonnet release cable into the car.

You talking about the frommit that exits kinda in the guard? And its a real pain in the ass to get to from both sides? :(

I did the same thing and poked a hole in if for wiring. its a bastard of a thing to get back in. I cant even remember if i did or not :s will find out in the enxt downpour i guess hehe.

Glad you found it tho! My old ITR had a leak in the boot that took me weeks to find. Ended up it was a crack in the seam sealer... dont even ask how i found that..

  • 13 years later...

I'm dealing with this issue currently. Makes me wonder whether it is somewhat common and people don't notice as long as it is not bad enough. Had spots of slightly damp carpet under the floor mats every now and then and always thought it came from the top. As in it dripped down from shoes or so. But it's definitely going from the vent under the windscreen down behind the carpets.

It must have gotten a lot worse recently. The foam under the carpet was just wet but not musty or anything. The foam under the plastic/rubber behind the pedals seems to have been wet for much longer as it smelled much more musty. On the plus side the car is now probably the driest it has been in a long time.

Booked it in to have someone who knows what they are doing have a look at it. Definitely no driving in the rain until then.

Some photos for what it's worth.

A cm or so of standing water under the carpets. Nice.

IMG_20220723_143709.thumb.jpg.59db6bc4af3aaa235b45bfc114f2c00c.jpg

 

Water goes in here

IMG_20220724_143107.thumb.jpg.f144f53834dded20caf3c2877047f03d.jpg

 

And part of the water comes out there

IMG_20220724_143152.thumb.jpg.4dea3b43401b6ae5e20a891c4d3eb107.jpg

 

Dry motherf**ker, dry!

IMG_20220723_161218.thumb.jpg.ed4113b664f12a1f05b872df3140a55a.jpg

 

IMG_20220724_150726.thumb.jpg.201ae0f614754a87ff9c350133105861.jpg

 

I panicked at first and almost bought a proper heavy duty drying fan from bunnings. In the end it turns out the shitty fan heater and old hair dryer work just fine.

On 28/07/2022 at 8:36 PM, GTSBoy said:

If it's not just blocked plenum drains, then it's windscreen frame rust. There's nowhere else for water to come from.

Wet driver's side is usually clutch master leaking out the back. But if you're sure it's water, see above.

Thanks for the pointers! Will have a look in the next days.

Plenum drain must be the worst name for it to go looking online. Closest I have found is this topic on MGs.

I'm not ruling out other things leaking, but pouring water into the vent ends up with at least some of it dripping down into the footwell.

The car has a mostly garaged history and little of the typical Stagea rust. So I'm keeping my hopes up that it's not a rusty nightmare hiding in there.

Any hints on where to look for that drain? Do the vents need to come out?

If you take your front wheel off then unclip the inner plastic guard liner, there are a couple of rubber grommets on the firewall that have wires and the accelerator cable etc going through them.

In their infinite wisdom, the jap workshops often slice these grommets to fit other wires for EVC and a/m gauges etc.  This then creates a leak. 

Some Sikaflex will fix it.

 

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh and I lost my headlight washer jet cover!
    • Ok, so I got myself some X1 wheels really cheap to try out, they're a bit different and I like them but they're really narrow (18x8) they are available in staggered 18x8/9 also but really hard to find.  I kinda dig them, but not as much as the F10 19's I usually run, so these go into the wheel pile.   As I mentioned in another thread, I got a new exhaust. It's an off-the-shelf stainless one that fits OH-KAY. I don't love the tips size and how far they come out the back, I think I might cut the tips off and replace with some smaller (~3") ones that don't extend as far. It sounds really good though, I'm not sure if its just in my head but the car feels a little quicker, more responsive.    I fitted an eBay special front lip. Surprisingly it fit perfectly and all holes lined up. Its a little rickety but I haven't put any double sided tape on yet, I want to clean the front bar up where it has scraped the road a lot and fil in the number plate holes (or, get body coloured wrap to cover them - is this a thing?  I'm not sure if I'll leave it gloss or pain it matte. I really like it though, I don't particularly like the front bar without it, I don't really like the M-Sport and to get anything else is just too expensive. That said, I might need a new one now anyway as I dropped the car onto the jack after forgetting to put ramps under the front wheels. It bent a lot and while it did go back to normal after I got the car off the jack, I do fear I have not done it any favours.   Lastly, my headlights died. Different problems in each. They have gotten much dimmer over the past year or so, I put new (uber expensive) OSRAM bulbs in them but to no avail. One of them pointed at the ground and the other just kinda did its own thing with light working sometimes. Yeah, check this 18 year old BMW headlight wire. I reckon I know why they were stuffed.       BTW, the yellow and black is the power to the Xenons. Yikes. I hunted around an researched my options here. I would have loved to just get a replacement harness but not a thing. My car has adaptive headlights, that is they rotate left and right with the steering wheel. Good condition used adaptive xenons were over $700 each, non adaptive were around $400 each, but I couldn't help but think that they're all around 18 years old now, surely they'd have the same problems. So I looked at newer LCI headlights but they were even more expensive and I couldn't confirm that they'd be plug and play with lots of people having lots of opinions so not worth the risk.  I ended up getting brand new Chinese headlights from MARS. They're very close to OEM with only the angel eyes being a bit different. I didnt want crazy turn signals or sharp DRL's or anything. Not my bag.  They're not adaptive, I thought thats a feature I wouldn't really miss. So I coded that out.  The lights are awesome, they look so nice and they take so many years off the car. The angel eyes look great and the headlight brightness is ridiculous. I was so used to the old ones, I didn't realise just how bad they were. The new ones use the OEM bulbs, Xenon ballast and leveller motor which I was happier with. The only issue with them is that the rear cover is held on by SEVEN screws. This will be a nightmare to get to and open when I need to change bulbs.  
    • Now that you mention it I can see those too. More subtle. The lighting and low resolution makes it hard to assess super well what's going on but what is visible is bad enough to pull the motor.
    • I feel like this is due an update
    • Yeah, I wasn't giving two f**ks for the ring running around the bore. I was looking at the vertical scratches running up and down across the hatch marks.
×
×
  • Create New...