Jump to content
SAU Community

Defect Cleared!

rad100

By rad100,
in South Australia

 Share

Recommended Posts

Bl4cK32 Grand Master

Bl4cK32

Posted
Posted
on second inspection they cant touch ya for anything else not seen first time round

Yes, but whats the point of having defectable items, that can be picked on as soon as you leave the door? If the ic piping is illegal, then fix it, and stay out of regency for good.

Iv never hade to go to regency so might be stupid But do they take ride hight from the lowest part of the car or from center of wheel to wheel arch?

Its not both. 100mm minimun clearance to the ground for the lowest point of the car, and then there is a set height from the centre of the wheel to the wheel arch. There is also an eye brow height as well it think.

Cubes Grand Master

Cubes

Posted
Posted

Its very wise to keep the heat shield on the turbo.

Radiant heat is a killer for your heater hoses. Should they spring a pin prick leak (as Troy's found out the hard way) glycol sprayed in a fine mist is highly flammable.

As for the front facing plenum... It alters emissions as the inlet is essentially used by car manufactures to tune a motors torque at various rpm. So yes it is defectable.

Elanor_S13 Contributor

Elanor_S13

Posted
Posted
Yes, but whats the point of having defectable items, that can be picked on as soon as you leave the door? If the ic piping is illegal, then fix it, and stay out of regency for good.

Its not both. 100mm minimun clearance to the ground for the lowest point of the car, and then there is a set height from the centre of the wheel to the wheel arch. There is also an eye brow height as well it think.

your right its actually depending on what sort of cop you get and how much he knows then to every defect question theres alot of differant answers >_<

Deluxe Grand Master

Deluxe

Posted
Posted
Yes, but whats the point of having defectable items, that can be picked on as soon as you leave the door? If the ic piping is illegal, then fix it, and stay out of regency for good.

Yeh but remember it only takes a cop to assume things and your back anyways! I guess it would only make your own life easier to replace stuff after!

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...