Jump to content
SAU Community

Hicas Lockbars - Ready To Be Shipped!


NV N01
 Share

Recommended Posts

Hi there,

I have access to Hicas Lockbars which are ready to be shipped :laugh:

I know there is already a group buy for this, but seeing as I have access to these I thought I would let you all know..

These Hicas lockbars will suit..

TYPE A:

A31 Cefiro

S13 (Silvia/180sx)

R32 (All types)

TYPE B:

R33 (All types)

R34 (All types)

post-16019-1178930233_thumb.jpg post-16019-1185690178_thumb.jpg

They are located in Brisbane..

Pick up is available :domokun:

They're $70 pickup..

Postage is an extra $15 Australia Wide

I personally guarantee fitment and strength..

I have used bars from this design on my own personal cars and have not had any problems with fitment or strength..

These WILL NOT Break or Twist like other designs ;)

We have even gone as far as "Crash Testing" them.. I kid you not, there was one in this 180sx and it rolled 3 times and the only thing still straight and unbent was the Hicas Lockbar from the same design.

Pm me or reply here if you are interested >_<

Regards,

Sherwin

post-16019-1182489686_thumb.jpg

post-16019-1182489723_thumb.jpg

post-16019-1182489939_thumb.jpg

Edited by NV N01
Link to comment
Share on other sites

  • Replies 135
  • Created
  • Last Reply

Top Posters In This Topic

Type A List

* R32drifter1000 - PAID & SENT

* Loren - PAID & SENT

* Predator - PAID & SENT

* Pg996 - PAID & SENT

* Subie

* Durty2

* Topaz - PAID & SENT

* Luke20t - PAID & SENT

* Femno - PAID & SENT

* Vsute - PAID & SENT

* DWN80Y - PAID & SENT

* GTS-070 - PAID & SENT

* Gt-t_R34 - PAID & SENT

* Turboedsloth - PAID & SENT

* Burnsie

* Embrace - PAID & SENT

* Betz - PAID & SENT

* Mahartika - PAID & PICKED UP

* Shagrath - PAID & SENT

* Choku_Dori - PAID & SENT

* Bubba - PAID & SENT

* gts25

* 12VES - PAID & PICKED UP

* Hadfield - PAID & SENT

* Heyhey! - PAID & SENT

* Heyhey! - PAID & SENT

* Sick R31 - PAID & PICKED UP

* RSTME - PAID & SENT

* Blck32 - PAID & SENT

* Jap32r - PAID & SENT

* James_03

Type B List

* Andi - PAID & SENT

* Darkon - PAID & SENT

* Crossie - PAID & PICKED UP

* Secur1ty - PAID & SENT

* Young Gun - PAID & SENT

* The Barman82 - PAID & SENT

* Evil_weevil - PAID & SENT

* KeyMakeR33 - PAID & SENT

* Gunmetalgrey - PAID & SENT

* Robbo33 - PAID & SENT

* d00dz - PAID & SENT

* White33gtst - PAID & SENT

* White33gtst - PAID & SENT

* Primordial - PAID & SENT

* Turbomad - PAID & SENT

* Meek34 - PAID &SENT

* Meek34 - PAID & SENT

* DrewR33 - PAID & SENT

* LTHLRB - PAID & SENT

* Apple_eater - PAID & SENT

* ahh 33 s2 - PAID & SENT

* Gtst25

* Sic.vlt

* Darkon - PAID & SENT

* Nuffin_Werks - PAID & SENT

* RPR33 - PAID & SENT

* 2BNVS - PAID & SENT

* EVL-R33 - PAID & SENT

* Tek_01 - PAID & SENT

* Mr 32- PAID & SENT

* Jaimzr33 - PAID & SENT

* Roadkillau - PAID & SENT

* Killswitch88

* Made_guy - PAID & SENT

* R33boy - PAID & SENT

* Wakesmeup - PAID & SENT

* HKS 3037

* Mikel - PAID & PICKED UP

* Fr33Sty13 - PAID & SENT

* Nawdie - PAID & PICKED UP

* Drf76 - PAID & PICKED UP

* gOt pSi - PAID & SENT

* lunjiaow - PAID & SENT

* Simmo1985

* Jurule - PAID & SENT

*

*

*

:P

Link to comment
Share on other sites

will there be any more of the type a's coming. i think these one will be gone by the time i get the cash together...

thanks simon

Hi Simon,

Yes there is a good chance that there will be more Type A Hicas Lockbars being made :D

The figure listed above are just the amount that is in stock ready to be shipped

:pwned:

Regards,

Sherwin

Link to comment
Share on other sites

ballpark figure on what they would normally cost to install?
second that, obviously including the removal of hicas

Hi there,

It around a 45min job to Do it yourself :D

There are a few articles in the technical section of how to do it step by step..

With that said.. a standard workshop hour can cost you anywhere between, $60-$120/hr, depending on where you go..

R32 Hicas Removal

R33 Hicas Removal

Regards,

Sherwin

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...