Jump to content
SAU Community

Recommended Posts

Hi,

Will deliver parts to your door within sydney, or possibly out of sydney..I have parts for sale off an R33 Gtst 95model s1.5. Located in sydneys west.

Willing to post at buyers expense. I can arrange personal deilvery/meet up in Sydney depending on certain conditions.

Prices Reduced

1. Front passenger seat - Good condition $150....$120

post-28122-1177924834.jpg

2. Drivers Side Seat - One tear in usual wear place $100....$80

post-28122-1177925279.jpg

3. Rear Seats - Good Condition $200....$150

post-28122-1177926151.jpg

4. Rear Parcel Tray - Like New $90....$70

post-28122-1177926877.jpg

5. R33 gtst Dash - Excellent condition $300....$250

post-28122-1177926998.jpgpost-28122-1177927027.jpg

6. Rear Window including Wiper and motors - In good condition/working order $150....$120

post-28122-1177927069.jpg

7. Front Window - Good Condtion $130 (pics available, but just a normal front window no cracks etc)...$100

8. Rear Quarter Windows - Good condition $50 each (pics available, but just a normal quarter windows no cracks etc)$35

9. Hand grips entire set (x3) - Good Condition $40 set....$25

10. Seat Belts ADR approved x4 - Great condition, off a complied and registered r33 $200(pics available upon request)$160

11. Left Hand drivers door - Good condition, includes window + motors (orange door) $150...$110

post-28122-1177927721.jpg

12. Right Hand drivers door - Good condition, window included, no window motor $120...$100

post-28122-1177927762.jpg

13. Front right hand side guard - Little dent at top of guard, easy bog repair $50...$30

post-28122-1177927840.jpg

14. R33 steering wheel, with airbag - Few scratches, car was in accident, unknown condition of airbag? $50

post-28122-1177928023.jpg

15. Skyline door panel - Good condition $40 pair

post-28122-1177928120.jpg

16. Fuel Cap Orange - Good cond. $20

post-28122-1177928241.jpg

17. Fuel kneck for compliance use - On complied/registered r33 $50

18. Roof Lining r33 gtst - Good condition $90

post-28122-1177928396.jpg

19. Interior Light middle of car $20

20. Interior light front of car $20 or For both together $30

21. Assorted Side interior panels - Enquire to what part exactly and I will give you a price. Alternatively make an offer. All in good condition.

22. Gtst orange guard indicators $30pair

Please send PM with your contact number and I will pm or call you back.

Please send PM with any offers or disputes and not post them on this forum topic.

Sydneys West

Link to comment
https://www.sau.com.au/forums/topic/166753-fs-r33-gtst-parts-wrecking-95-s15/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...