Jump to content
SAU Community

Autronic Sm4 And Cdi

Snowman
 Share

Recommended Posts

Snowman Grand Master

Snowman

Posted
Posted

Guys,

I'm selling my Autronic SM4 ECU (Autronics best ECU) and direct fire CDI unit.

I've had them for less than 6 months and the car basically hasn't driven in that time. I need to sell them to pay for some bills. :P

Information on the units can be found at:

Autronic SM4 - SOLD ($1800)

Direct Fire CDI - http://www.autronic.com/page_files/direct_fire_cdi.htm

I also have an RB26 trigger disc to suit.

Price: $800 for CDI only

PM or contact me on 0419 375 140.

Link to comment
https://www.sau.com.au/forums/topic/167388-autronic-sm4-and-cdi/
Share on other sites
Snowman Grand Master

Snowman

Posted
  • Author
Posted
Loom setup for skyline I'd assume?

Any other sensors with the Autronic?

Cheers.

Pretty much there isn't going to be a loom. Well there is going to be about 1ft of loom as the autronic was spliced into the standard loom in my car rather than had a seperate loom run.

-Totenkopf- Enthusiast

-Totenkopf-

Posted
Posted
Pretty much there isn't going to be a loom. Well there is going to be about 1ft of loom as the autronic was spliced into the standard loom in my car rather than had a seperate loom run.

Well that sucks nuts. I'd need a full flying lead for custom installation. Don't guess you know the going rate of a replacement flying lead loom? I couldn't find anything doing a google.

Ah well, was considering an SM4 from the get go but couldn't find one, so I purchased a Haltech E11V2. Don't think I'll bother switching if its going to cause me a heap of grief.

Cheers,

James.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      Sane enough. Remove the roof liner, because the acid will go everywhere.
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks guys, I really appreciate the help and experienced opinions.  I have spent a lot of my life working on boats so I'm pretty good with fibreglass. I'll take everybody's advice in here;  I'll cut a little more of the 2nd layer away as it's a bit crunchy rust and also it's sitting high now. Then I'll wire brush it all a bit to get off anything loose, then I'll soak the bejesus out of it all in rust converter. I'll make sure to get a little hose piece and feed it into all the holes and gaps between the roof layers. Then I'll fibreglass up the holes.  Then I'll get a pallet of filler and mix it with 3 buckets of hardener and hope that is enough to build up the roof corner.  Does that sound sane? Is one type of filler better than others for this?
    • jtha7
      New r33 owner

      By jtha7 · Posted

      My goals for it atm are to get it registered, respray and some mild power gains eventually... I picked up the car from an elderly gentleman near the border of NSW and VIC, its honestly a bit rough and looks like its been driven on a farm (because there was so much dirt underneath). Last week I dropped the subframe and emptied the old fuel out + added a new fuel pump (think the old one went bad from old fuel). Now I'm onto fixing a coolant leak at the rear of the engine + adding a new radiator as the old one is corroded. After that i have a new bumper, coils (as the old were leaking) and lots more
    • Shizu
      New r33 owner

      By Shizu · Posted

      Welcome buddy! Plenty on here and YouTube. What are your plans for it? Good luck with the Rwc and Rego bud!
    • soviet_merlin
      The Evolution Of "night Fury"

      By soviet_merlin · Posted

      Love this so much! Please post a photo when you have a bike on the trailer.  I was a little bit worried about having a tow bar on the Skyline, but having it hidden behind the number plate is genius
×
×
  • Create New...