Jump to content
SAU Community

Wa Stagea Compliance

kieran777
 Share

Recommended Posts

kieran777 Apprentice

kieran777

Posted
Posted (edited)

Hi guys,

ive heard that there is around 2 compliance places in perth that do stageas, but ive also heard that they are not exactly the most helpful of organisations.

(ben fom j-spec imports advised me of this)

i was just wondering if any WA stagea owners can give me an insight as to what places they used for compliance and how it went...

just so i can avoid any pricks with compliance.

Cheers

Kieran

note - referring to stagea rs four v/s compliance

Edited by kieran777
Link to comment
https://www.sau.com.au/forums/topic/167702-wa-stagea-compliance/
Share on other sites
Wildcat Grand Master

Wildcat

Posted
Posted

I had my stagea complied in Perth less than 12months and i would definately NOT RECOMMEND who i used...they cost a fortune, they were slow, they were rude, they were definately not the most helpful people, not to mention that they run my car out of fuel which caused big problems and they couldnt care less!!!..They were also the only WA compliance place at that point in time!

If you want to know my story ill chuck you a PM as i cant name them on here for rules of SAU...but i would definately be looking else where instead of using these people!

kieran777 Apprentice

kieran777

Posted
  • Author
Posted (edited)

Thanks for the PMs and reply guys.

It really is appreciated.

To me, it seems that the best decision to make is to have the car complied over east by a recommeded business, and have it shipped/freighted out to perth.

J-Spec advised me that the compliance market is far more competitive there,

and seeing how they can freight for around $500 to perth (due to the govt rebate) i probably wouldnt be anymore out of pocket than forking out an unjustified amount for a shitty perth compliance.

I assume that compliance over east would still enable the car to pass the pits over here, right?

Cheers

Kieran

Edited by kieran777
Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

quite easily

you won't be the first to do it that way and you sure won't be the last

good luck with it and looking forward to seeing yet another join the ranks in WA

ssshonky Grand Master

ssshonky

Posted
Posted

we are getting ours complianced in QLD , so cant YET comment on workmanship

but basically we got ours complianced in QLD and shipped over for CHEAPER than we could get it complinaced locally

got the J-spec page for your car so we can look?

did you get the 50billion photos they take too?

kieran777 Apprentice

kieran777

Posted
  • Author
Posted

alrite that sounds like a good idea then.

i spose brissy compliance would be the best...boats get there first, so its gonna get the ball rolling sooner.

especially considering alot of people have done it without any hassles.

cheers for that guys!

PS the link was taken down so no pics atm sorry

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      braided lines for the turbos

      By GTSBoy · Posted

      For your application, where you'll be at that 1/2" size or perhaps larger, yeah, excellent. Although not if you need a tight bending radius anywhere, because the corrugated stuff is not anywhere near as flexible as rubber/teflon cored stuff. But for turbo oil lines? No. Too big. They just don't do the corro stuff down at the ~1/4" ID size that you'd want, and if they did the OD of it would probably be a bit too fat for fitting it into the tight spaces available. I use hoses like that all the time for fuel gases (LPG, NG) and liquid fuels (HFO, diesels, waste oils). When we did the London Olympic cauldron, with the 204 individual burners on it, we had miles of the stuff (although a lot of that was teflon core). A bunch of that crap is still cluttering up the workshop, more than 12 years later!
    • The Bogan
      braided lines for the turbos

      By The Bogan · Posted

      Would something like this be an option  https://processhose.com/products/configurable-metal-hoses/1-2-in-t316-stainless-steel-annular-corrugated-configurable-flexible-metal-hose-assembly-with-ends-t304-single-braid-masterflex-af5550.html I'm looking at this for replacing the OEM EGR when installing a aftermarket intake plenum 
    • r32-25t
      Unpeeling the Orange

      By r32-25t · Posted

      The once piece tail shafts with cv type joints on either end are the ones that end up vibrating and the vibration is caused by the cv joint binding as it turns, I’ve also seen them explode from the binding 
    • Kinkstaah
      braided lines for the turbos

      By Kinkstaah · Posted

      Take this with a pinch of salt, it's from someone (me) who got annoyed with turbos entirely. I hated aftermarket lines. If I had the option to use hardlines with whatever turbo I had - I would use them, 10/10, 100% of the time. The only reason people go larger, heat resistent, shielded lines etc is because they have to. And yes they don't last forever. Even if you spend big bucks on all the best heat shielding money can buy, with the best heat resistant, fuel resistant, oil resistant, radiation resistant hose, they get stiff and break down and just don't last the way a metal pipe will.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Unfortunately I am quite literally halfway across the globe. So all sources for parts like that are far away for me. What do you mean by that exactly?
×
×
  • Create New...