Jump to content
SAU Community

Recommended Posts

1997 AUTECH 260RS

RB26DETT powered 4WD Wagon

86,000Kms - PEARL WHITE

Normal AUTECH Gear like Brembos, Dual Airbags, and Bodykit

$34,000 - Reg exp 03/08 URE-431

EXTRAS

TEIN Coilovers - Fully Adjustable

KAKIMOTO Turbo back exhaust -

AVC-R tuned with 0.8 and 1.2 Bar settings

HKS Turbo Timer

Twin HKS Pod Filter

G-Reddy Oil Catch Can and pressure Reg

G-Reddy pillar mounted Boost guage (along with the normal Dash mounted guages!)

I imported the car Early Jan 2007 - Have absolutely loved driving the car, but realised it just isn't me anymore (much to my Fiance's relief).

The car is in awesome condition and totally exceeded my expectations when it arrived off the boat - would consider a swap with anything a bit more conservative along the lines of Audi A4/S4 or maybe BMW M3 etc

The interior is in immaculate condition and the only damage on the car is the usual Front bar scratches underneath and a small chip which is visible on the front bar lip. The Car was graded 4BB at the Auction house in Japan.

The car is in Melbourne and i can be contacted on 0410 85 88 94

OR by PM.

Cheers,

Tim

http://www.carsales.com.au/used-cars/priva...matchallpartial

Edited by Herbietjh
Link to comment
https://www.sau.com.au/forums/topic/169193-autech-260rs-1997-for-sale/
Share on other sites

  • 4 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...