Jump to content
SAU Community

Best Way To Pipe Front Mount Intercooler?

jUsT-dRiFt-iT
 Share

Recommended Posts

RBwhatever Veteran

RBwhatever

Posted
Posted
Does anybody have the link on how to cut the hole??

If your wondering where you have to cut the hole, just get the kit and dummy fit it, that'll tell you where.

The hole should end up being just under the washer bottle.

Mark out where the hole is going to be then stitch drill it. A die-grinder comes in handy to smooth the edges.

After the put some rubber edging around the edge of the hole to stop the metal rubbing on the aluminium piping.

Remember to dummy fit the whole kit and intercooler together to make sure everything will line up.

RBwhatever Veteran

RBwhatever

Posted
Posted

No the bottle stays where it is. It shouldn't have to move the whole time the kit is being fitted.

http://www.skylinesaustralia.com/forums/in...tercooler++hole

Here's a link. Look at post #10 for a couple of pics.

Its pretty much where the hole should be. Although don't just take his measurements and chop the hole out. Please dummy fit it before cutting the hole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Dose Pipe Sutututu
      Intercooler Choice

      By Dose Pipe Sutututu · Posted

      Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...