Jump to content
SAU Community

Recommended Posts

hi guys,

I'm after the two radiator hoses for an r33 rb25det engine.

Know anywhere in SE Melbourne that supplies it?

Also another question. I recently replaced the radiator because it died on me the other day and found that there is a bolt with a wire that attached to the original radiator (some kind of sensor, that attached to the bottom left of the radiator tank). Well I couldn't find a place to put that after getting another radiator from the wreckers as the original place where it was supposed to go was sealed. Well I've been driving without that sensor and their doesn't seem to be any problems so far but just to be on the safe side I thought I would ask.

Also how do I go abouts flushing the radiator and the coolant system? Is there a plug or screw that lets the stuff out while I run water through the top of the radiator?

And what coolant do you guys recommend. Right now I'm using concentrated coolant and mixing that with water. Is premixed better? 33% ratio? Theres just so many types.

Sorry for all the questions. :)

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/
Share on other sites

Autobarn carries most of this stuff now.

I use Nulon too.

If you have a look on the left hand side of the engine near the plenum you'll see a brass colored pipe (not the fuel rail) running up along to top of the engine (at least it is on mine) that feeds water. It has a small screw on it. If you drop the radiator fluid then refill it with the engine running and loosed the screw you'll bleed all the air out as you fill. Works a-ok for me and no air locks. You'll need to pull the bottom hose off to drop the fluid.

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/#findComment-3135094
Share on other sites

The 180 and gazelle both have a plastic plug right underneath on the passenger side.. of course one of them was brittle and snapped when I first got the 180.. had to pull the whole freakin radiator off and bang it upside down to get it out lol.

Luckily they are the same size :)

Here.. try this, bottom left.

post-19275-1179887186_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/#findComment-3135150
Share on other sites

yeah with that air release valve on the plenum

when do you know all the air is out

because mine just keeps bubbling light green foam out, but i never see the coolant actually come out.

And do you do this with the radiator cap on or off?

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/#findComment-3135180
Share on other sites

searching for radiator hose was the biggest pain for my car.

No one stocked it in the SE subs, repco, autobarn, supercheap (from Ferntree gully to Dandenong) none of those shops had any replacement.

In the end just bought a new radiator hose from Nissan Ferntree Gully. Ordered 9am morning, received 3pm same day.

But ive head from a friend, that autobarn now sell radiator hoses for $100 pair.

Flush radiator, there should be a little tap screw under the radiator and a small rubber hose. Unscrew and it should pour out.

Used Nulon 50% mix. Took ages to do and was a pain to flush the radiator.

Radiator workshops charge $30 to flush radiator (thats including coolant supplied)

Cheaper to just go with a workshop than to stuff around by your self.

Cheers

Patrick

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/#findComment-3135294
Share on other sites

yeah with that air release valve on the plenum

when do you know all the air is out

because mine just keeps bubbling light green foam out, but i never see the coolant actually come out.

And do you do this with the radiator cap on or off?

I had radiator cap on and left the air release valve open.

I also had a shit load of white foam coming out, panicked and thought it was oil in radiator (as oil in radiator causes white foam)

The bubbling you and I saw was the new coolant reacting with the old coolant. So you didnt do a proper flush me thinks.

Look in the R33 workshop service manual for a step by step guide if you want to do it yourself

Cheers

Patrick

Link to comment
https://www.sau.com.au/forums/topic/169653-radiator-hose/#findComment-3135303
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's impossible to convey what it will feel like to get the right torque. But you can develop a feel for it. A 900mm breaker bar is.....f**king huge. I only use a normal ~400mm one. But with 900mm being very nearly a metre, and the right torque being in the order of 100Nm, then you're going to need a bit over 100N of force, which is about 10 kg. So if you practice using the bar pulling up, instead of pushing down, then it will be about the same effort as lifting a 10kg bucket of water. That's what the pressure against your fingers should feel like. Ish. If you use a more typical length breaker, then it's about twice that. So a good 20 litre bucket, or a little bit more.
    • Also, if anyone has a torque wrench around Williams Landing area and can lend it to me for like 5 mins - I got 4 bottles of Furphy left and I’ll throw that in with a Happy meal 😂
    • So today I decided to bleed my brake fluid, which meant to the wheels came off the car at my garage for the first time. I only had a 90cm breaker bar with me and I noticed that some 1 or 2 lug nuts were a bit hard to get loose (from when the shop did the coilovers) Now.... when it came to putting them back on, I didn't want to put all my weight and overtighten them. So I hand tightened as much as possible and then put normal pressure on the edge of the breaker bar and tightened it until I couldn't turn it anymore without putting in an effort. Do you think that is tight enough? Or is that still too tight?  They are tighter than finger tight. Last thing I want is to have them strip or warp sh*t. But hard times mean I can't just go down to Supercheap and get a torque wrench 🥺
    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
×
×
  • Create New...