Jump to content
SAU Community

Recommended Posts

Ok first the car is a S2 R33 GTST with front mount, 3" catback & pod. In the last couple of weeks, there have been a couple of cases where I accellerate hard and around 4-5k rpm the engine has hit a limiter.

The limiter feels like a fuel cut, if you have ever been to the speed limiter in 5th gear (~5500rpm) its a bit like that. Happened this morning in 2nd around 4-5k rpm...

Anyone know what would cause this? I'm pretty darn sure it wasnt the 7k limiter.. its a bit faster then that.

Cheers,

Ryan.

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/
Share on other sites

Just stock boost. It only lasted 1 second at the most... definately not the rev limiter.

I've hit speed limiter (fuel cut pretty much right?) in the non turbo and its similar to that, much quieter then a rev limiter. Like a low fast rumble..

Edited by SKY RYAN
Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3135940
Share on other sites

Yeah just drove home and went to overtake someone in 2nd and it did it.. then on the freeway i droped down to 4th, then to 3rd and gave it stick and yeah it did it again...

So coilpacks eh, is it bad to drive like it is now? or can i just drive it soft..

EDIT: Wer can i get me sum coilpakz!!1!1

Edited by SKY RYAN
Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3136084
Share on other sites

Talk to paul and Alistair. See what they say. I dont think it will be warranty though.

If you do want to get them from Slide, let me know as i need to order a set for for an SR aswell. We can do 1 order and try to save a bit of freight :)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137401
Share on other sites

I'd be checking all your silicon joiners.. I had a hose clamp pop off (just the clamp not the silicon) and when it got to about 4k it felt like it hit a wall.. took me a bit to figure out as it wasn't like when the hose popped right off (when it popped right off it wouldn't idle and pumped HEAPS of black smoke).

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137711
Share on other sites

the split fire coilpacks are easy as to replace, yeh you have to take off that black cover, its about 8 screws that require an allen key,

under that is the coilpacks, just have to unclip the wiring loom they are connected to and then each coilpack has 2 screw holding them down,

just take the old ones out and pope the new splitfires in, easy :P

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137807
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...