Jump to content
SAU Community

Recommended Posts

i have a 40th anniversary sII gts25t and i have some problems the car first of all has a small air leak from the fuel rail thats a little bent out of shape and its not sealing, but it still boosts up to 7 psi but the car is really slow, a n/a stock sr20 is faster, the car kind of slugs its way up the tach then at high rpms you start to feel a little push but thats about it the compresion is fine the idle is fine it sounds liek all the cyl's are firing its just uber slow, any suggestions? heh i know its not too discriptive but some help would be highly apreciated

Link to comment
https://www.sau.com.au/forums/topic/169941-rb25det-problems-please-help/
Share on other sites

the fuel rail isnt stoping fuel flow, the previous owner i suspect tried toforce the fuel rail out or something and bent it upwards 1 of the injectors isnt totally flush with the manifold so its sucking/blowing air through thier only 1 injector though

the fuel rail isnt stoping fuel flow, the previous owner i suspect tried toforce the fuel rail out or something and bent it upwards 1 of the injectors isnt totally flush with the manifold so its sucking/blowing air through thier only 1 injector though

That cant be good....

I would take 1400r advice or go see mechanic. before you melt a piston. and check that injector?

Guest 40th-edition

check your Airflow meter for gunk, and clean with throttle body cleaner, may aswell hit the throttle body with some as well..

may have an exhaust leak in the manifold so listen for that and check.

check your O2 sensor and fuel pressure.

could be heaps of things man, so check them and see how you go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This would be a new pump with new gears. I'm just unclear on whether it's a good idea to run more oil pump flow if you don't actually need said flow. Oil level is set a minute or so after shutting off a warm engine so wouldn't the high RPM oil level in the sump end up lower all things equal? Plan is OEM clearances, main concern in my mind is whether the OEM pump can keep up with the flow requirements of any additional oil coolers.
    • Don't do what I did, use a 300000km old housing with billet gears. The old pump probably was clearanced with saw dust, Edward Lee's special engine treatment sauce and a good odo wind back. I had oil pressure issues, then replaces pump with new housing, new billet gears and 2x track day later binned a motor due to other oil related issues due to a previous engine builder. Long story short, buy a M2 or 3 or 4 N55/S55/S58 and enjoy life.
    • Yeah. "New pump" does not have to mean "massive pump".
    • Well, can you still get an OEM pump, and by the time you're buying a Nismo/N1 etc, just buy another aftermarket pump. It's better to have the pump able to flow more if its needed, than for your pressure to drop off. At any point in time, you're replacing the oil pump in a rebuild. Aftermarket pumps are likely going to be a better economical choice, and they don't have any negatives, even if they can flow more.   Also, when you're saying "replace the pump gears" are you meaning leave a 25+ year old housing in the engine with unknown wear, and just put new gears in? As that sounds silly to me, especially if you do have that minute amount of wear, that means your new pump gears now have a little bit more clearance beside them, which means, whelp, you may not get to build a lot of oil pressure or make a lot of flow.
    • Right, but if you replace the pump gears + put a spline or sine drive gear on the crank on a Nismo/OEM/N1/etc pump at that point do you really still want more flow/oil pressure? Let's say this is a the aforementioned "keep it simple" build, no more than ~400 kW at the crank.
×
×
  • Create New...