Jump to content
SAU Community

Recommended Posts

I have this little problem with my 33 gtr where i get intermittent loss of power. Its stock standard not even an exhaust.

This is what i have discovered so far,

When i first start the car in the morning when its cold, it seems to be lacking a bit of response, but i dont push it, it just feels that way down at the low revs. Maybe thats what its meant to be.

Once the water temp gauge goes up to where it should be, the car feels good! the response and power is how it should be. But SOMETIMES after driving for a while like 30 mins plus, sitting in traffic here and there and when the oil temps are up to about 80C it feels like it is a bit hesitant to go at lower revs and it feels slower through the rev range too. Almost feels like it doesnt want to go for a second or so and then slowly the power comes on.

But then when i turn the car off for a while, come back after 20 mins drive it again and it feels like normal again, pulls hard and all. WHat the hell is going on?????? Can sometime tell me what it could be? Ignition timing hasnt been touched, plugs are correct too.

Link to comment
https://www.sau.com.au/forums/topic/169970-strange-problem-with-gtr/
Share on other sites

Next time it does it check the boost gauge to see if she boosts as normal, if it doesn't boost to normal I think I know what it is. If she boosts normal look at electrical stuff, like coil packs, plugs etc...

Its running the stock air box with a hks panel filter.

And the boost seems to be normal, it just doesnt want to pull as hard. Under say half throttle in 2nd gear around 2-4krpm it feels flat and laggy. But then i stop to get petrol, start it up a few mins later, its feels much better again.

My mech plugged it into a diagnostics thing and reckons ignition timing is ok. he also reckons the coils and sparkies are fine and he reckons the afm is ok too. He is kinda stumped too, but I havent realy been able to show him the problem properly as it is intermittent. He reckons it drives fine because he hasnt experienced the changes in performance.

He was suggesting a possible fuel pump problem?? could it be possible?

It sound like the ecu is seeing knock and then using the low octane ignition map to protect the engine. Turning off and on allows the hi octane map to be used.

I had a similiar problem on GTSt, it was detecting knock just off idle when at operating temp, try retarding the timing 2-3 degrees at the CAS.

  • 2 weeks later...

I have a similar problem except mine's in a 32 Gtst with a RB26 convertion. At low rev's specialy in 1st and 2nd gear.

I go to take off and its like the turbos are straved or something, it will slowly boost up then drop out.

But if I take off on high revs, its fine.

Can't think of what the hell it could be.

My car has the same problem from the sounds of it. I'm running 1 bar boost (restrictor removed from standard setup) and all your standard mods. For me, the car drives perfectly for the first 10 mins or so, making 14psi or so. Then it hesitates for half a sec, becomes sluggish and will only boost to 7 psi, but it feels flatter than when the car was running that boost standard.

I can then turn off the car, restart it instantly and its nice and responsive again, making 1 bar again. It clearly electrical but i get no warning light on the dash to say somethings wrong and i cant figure it out. I figured either afm's or my boost solenoid? Sounds very similar to your dramas, probably the same item giving us greif.

Not sure what's going on there Phil.

I have never experienced that problem in mine.

In regards to driving it first thing in the morning when its cold, mine is very spluttery if it goes over 3k rpm. But as soon as its mildly warm its fine for the rest of the run (whether its a 5min or 5hr drive).

Hope you can find the problem, fix it and let us know for future reference!!

- Dave.

Not sure what's going on there Phil.

I have never experienced that problem in mine.

In regards to driving it first thing in the morning when its cold, mine is very spluttery if it goes over 3k rpm. But as soon as its mildly warm its fine for the rest of the run (whether its a 5min or 5hr drive).

Hope you can find the problem, fix it and let us know for future reference!!

- Dave.

Exactly the same things happens to mine when its cold. As soon as you hit abit of positive pressure it starts to splutter but when its up2 normal driving temp its fine.

That's normal for the stock ECU, mine used to be like that when it was cold in the morning, as soon as the water temp hits (can't remember) it switches from open to closed (or is it the other way around) mode... and it runs good/normal. When i switched to a PFC i don't have this anymore - but not like i fang it when cold anyway, so it makes no difference.

As for driving it for 30mins and then it dropping boost from 14 to 7, there is something wrong there.

  • 2 weeks later...
That's normal for the stock ECU, mine used to be like that when it was cold in the morning, as soon as the water temp hits (can't remember) it switches from open to closed (or is it the other way around) mode... and it runs good/normal. When i switched to a PFC i don't have this anymore - but not like i fang it when cold anyway, so it makes no difference.

As for driving it for 30mins and then it dropping boost from 14 to 7, there is something wrong there.

Recently in the colder temps i noticed it is happening more often like in the mornings and nights when its like 5 degrees or so. Warmer days seem to be ok asnd doesnt happen as much.

Strange thing is, it doesnt do it when i thrash it, it seems to happen under low revs and low boost etc, low throttle. Sometimes I give it the fang up to 14psi and its fine still. I also disconnected the boost solenoid so it runs 7psi but still does it. So its not a high boost issue. Something to do with too much air flow, but why? grrr

I have a PFC coming to im going to throw it on the dyno to see whats going on and hopefully fix it or at leats know what to fix.

  • 5 months later...

I recently replaced my r32 gtr afm's with r 33 gtr afm's and since then it has been messing up at low rev's as well, same business, unless i give it to it (which i won't because it's cold) it feels damn slow and damn laggy.

Once it heats up it's all fine though

I regapped my plugs from 1.0 to .8 at the same time i put the new afm in, im gonna try re-gap my plugs to 1.0 again tonight and see if it makes a diff

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
×
×
  • Create New...