Jump to content
SAU Community

Compressor Surge

iz32

By iz32,
in Engines & Forced Induction

 Share

Recommended Posts

iz32 Community Regular

iz32

Posted
Posted

I have just been reading up on compressor surge all afternoon particularly in relation to low rpm on an RB20. i have dug up some stuff on sau regarding this topic when incorrect wheel configurations in highflows can cause a compressor surge at low rpm, what im unclear about is would this only occur at full boost or can it also occur whilst building boost? and how?

as i understand from what i have read is that the compressor wheel will push x amount of air out and if the pressure between the turbo and engine is greater then what its pushing then it will be forced back thru the compressor causing surge.

now how would this occur in a low rpm situation when the boost pressure isnt that high?

what causes the engine to restrict this compressed air entering the combustion chamber?

could an incorrectly setup engine cause surge or is it all to do with a spiking turbo?

i have theories on incorrect inlet cam lift duration or timing....but im not a qualified mechanic or an engineer and could totally be off the mark so opinions would be great!

Link to comment
https://www.sau.com.au/forums/topic/171149-compressor-surge/
Share on other sites
InterCooL Rising Star

InterCooL

Posted
Posted (edited)

surge typically occurs when you start to build boost, the blow off valve is not going to vent at low pressures, so the air gets pushed out the compressor. can happen at 0psi, can happen at 20psi, pending if u how tight / if u even have a blow off valve

does that help?

Edited by InterCooL
iz32 Community Regular

iz32

Posted
  • Author
Posted
surge typically occurs when you start to build boost, the blow off valve is not going to vent at low pressures, so the air gets pushed out the compressor. can happen at 0psi, can happen at 20psi, pending if u how tight / if u even have a blow off valve

does that help?

it does clarify that point but im also trying to figure out where the problem occurs in the engine. as positive boost builds it should be drawn/forced into the chambers so what would cause it to bank up and surge?

in my particular case the turbo is a constant and 2 different engines are the variables...

edit: i should add that im refering to during the spool phase... not off the throttle BOV type scenario.

InterCooL Rising Star

InterCooL

Posted
Posted
edit: i should add that im refering to during the spool phase... not off the throttle BOV type scenario.

you're getting surge when you are spooling up? :)

you cannot be doing that. you must be mixing 'surge' with something else. but i cant imagine what

iz32 Community Regular

iz32

Posted
  • Author
Posted

yer im really confused...

I just cant understand how 2 RB20's can behave soooo extremely different with the same tune and mods hanging off em.

just relating everything i can find to the situation.... SAU is killing my brain cells

--END THREAD--

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
you're getting surge when you are spooling up? :)

you cannot be doing that. you must be mixing 'surge' with something else. but i cant imagine what

Yes you can have that.

You can have compressor surge as you build boost.

Generally due to a comp wheel that's too large to the rear. Can happen in low RPM definitely as boost is created.

Basically the comp wheel is flowing more air that the motor wants at that stage, once you overcome this its ok usually

bazr33 Mentor

bazr33

Posted
Posted

i notice compressor surge on my r33 with a plain bearing hiflow, Front wheel was off a isuzu truck. Old skool design To4

what appeared to be happening, is that the turbo was generating way too much air that what it should of, at start of spool phase.

This was at 5psi, and then we believe the bov started to pulsate, pushing air through the plumb back pipe into the intake, then too my afm.

The afm recognised more amount of air, getting pushed through, so it dumped more fuel into the engine. I didn't notice this surging when i have the standard airbox on with my standard afm, as it mighten of not of been as sensitive as the z32afm, and the apexi pod filter being able to suck ???

I didn't get around to fix this problem, but i believe it was either relocating the afm to another position, change the bov to atmo, or putting a stronger spring in my BOV.

Then again these ideas could not of worked either.

I have now changed turbo setup, so see what happens. (also going to put a sharp bend in for my intake pipe)

Slim Mat Collaborator

Slim Mat

Posted
Posted

Yo, IZ32

Please visit Garrett's website:

http://www.turbobygarrett.com/turbobygarre...bo_tech103.html

This is all pretty advanced stuff, just read through and filter out most off it and learn what you need to know about Surge. There is a few paragraphs about a 1/3 down the page.

This should help explain it a lot.

Slim

InterCooL Rising Star

InterCooL

Posted
Posted
Yes you can have that.

You can have compressor surge as you build boost.

Generally due to a comp wheel that's too large to the rear. Can happen in low RPM definitely as boost is created.

Basically the comp wheel is flowing more air that the motor wants at that stage, once you overcome this its ok usually

i had a gt2876r 0.86.

massively oversized compressor relative to the exhaust wheel. renown for it. i hated the setup. but i never had any strange induction / surge noises

not saying its not possible, but if a gt2876r doesnt give you it, then you're not going to be getting it with a hks2530 that iz32 is using?

Hardman69 Collaborator

Hardman69

Posted
Posted

Happens with big (relatively speaking) boost, at low rpm. If you look at a compressor map for a turbo, you'll usually see a dotted "Surge line" running up the L.H.S. of the map. This is where the compressor can't push any more pressure at that flow-rate, and stalls (like an aeroplane wing stalling, or a boat propeller cavitating). It stops pumping & sheds a tonne of boost pressure and (turbo)rpm, until it can re-establish compressor flow & start building shaft rpm & boost again.

If U keep the clog in, this keeps happening in a cycle, and U get compressor surge. Wind down the boost at low rpm, or back off the throttle when U hear it hissing REAL loud just before it stalls (and makes the ssssSSSSSCCHHEEW sound as it stalls the compressor). Good luck :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Randhj
      R34 4 door indicator and horn issue

      By Randhj · Posted

      Thanks, I removed the fuse and the relay from the car and made my own circuit with them to test them with a test bulb.  I will look for the wiring diagram and go from there.
    • Milkmun
      The FD RX7 is the best looking 90's JDM car

      By Milkmun · Posted

      Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • PranK
      The FD RX7 is the best looking 90's JDM car

      By PranK · Posted

      Gotta admit, I love the 20b Cosmo.
    • joshuaho96
      Nismo Super Coppermix Twin and R33 GTR transmission replacement

      By joshuaho96 · Posted

      Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
    • PLYNX
      The FD RX7 is the best looking 90's JDM car

      By PLYNX · Posted

      Of the 90s ! !
×
×
  • Create New...