Jump to content
SAU Community

Trust Wing For R33

cruzin33
 Share

Recommended Posts

Spunky Munky Grand Master

Spunky Munky

Posted
Posted

The kit is a bit like the OEM GT-R one - only more chunkier at parts and is rather more boxy.

With the wing, it's not bad, only if it had only 1 level.

And yeah, sorry, can't help you with the wing thing - never heard of it.

lineskee 33 Community Regular

lineskee 33

Posted
Posted

I agree where can i get one of these too? I have looked absolutely everywhere and i cannot find them. especially for a good price. any fibreglassers out there willing to make copies of an original?

lineskee 33 Community Regular

lineskee 33

Posted
Posted

They are not easy to come across. I had enough trouble finding a picture of one of these. I have tried searching for places that sell them and I had no luck. I really want one of these wings too. I only seen it on this car and the DRAGME skyline.

post-26692-1181835788_thumb.jpg

  • 2 weeks later...
Spunky Munky Grand Master

Spunky Munky

Posted
Posted

Fellas, looks aside... might be an issue with the cops as the wing is sticking slightly too much towards the sides - you may get a canary for this... I had a GT like wing on a couple of months back - got defected as well... just watch out... check before you buy (not that you'll find one any time soon anyways)...

PSI Parts Veteran

PSI Parts

Posted
Posted

I to am wanting one of these wings and yes they are as rare as rocking horse shit. They are not actually a trust wing, they are a Garage Saurus wing. I'm willing to make these if someone can find or let me borrow an original.

For those with Hyper Rev mags, see page 143 of Skyline GTS No.3 Vol 60 for another pic.

post-28667-1183463674_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
×
×
  • Create New...