Jump to content
SAU Community

Recommended Posts

I don't think this has been posted before, but I have been searching for it for a long time and I'm sure atleast a few SAU members would be interested in it.

http://www.dotars.gov.au/roads/safety/bulletin/vsb_ncop.aspx

* NCOP1 Preface 3 Feb 2006

* NCOP2 Intro 3 Feb 2006

* NCOP3 Section LA Engines 3 Feb 2006

* NCOP4 Section LB Transmissions 3 Feb 2006

* NCOP5 Section LG Brakes 3 Feb 2006

* NCOP6 Section LH Body Modifications 3 Feb 2006

* NCOP7 Section LK Seating and Occy Protection 3 Feb 2006

* NCOP8 Section LL Motorcycles 3 Feb 2006

* NCOP9 Section LM Fuel Systems 3 Feb 2006

* NCOP10 Section LO ADRS ICVs 3 Feb 2006

* NCOP10A LO1-3 ICV checklist 3 Feb 2006

* NCOP10B LO1-4 ICV checklist 27 Jan 2006

* NCOP10C LO7 ICV Motorcycle Checklist 27 Jan 2006

* NCOP11 Section LS Suspension and steering 3 Feb 2006

* NCOP12 Section LT Test Procedures 3 Feb 2006

* NCOP13 Section LV Alternative Power 3 Feb 2006

* NCOP14 Guidelines Electric Drive 3 Feb 2006

* NCOP15 Trike Guidelines 3 Feb 2006

* NCOP15A LEM Trike checklist 27 Jan 2006

* NCOP15B LEP Trike checklist 27 Jan 2006

* NCOP Cover Page

:woot:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Isn't there a fitting on the back of the balance tube? That's what the OEM boost gauge uses.
    • Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
×
×
  • Create New...