Jump to content
SAU Community

Recommended Posts

My R33 struggles to start from cold. In the morning I'll start it and will need to really pump the accelerator before it will take. Every other start after that will be fine, but the next morning it struggles again. I always leave it on ignition only for a few seconds for the whole thing to get ready before I actually start.

From reading just about half the posts on SAU I have found that this is a fairly common problem and there are many possible causes :worship:

I think I have narrowed it down though and need some other opinions

I have a volt meter in my car and when starting it will drop to about 8 volts... from what I understand... this is way too low

If I understand correctly, this is caused by the starter motor arcing due to worn brushes

I was thinking of getting a starter motor from a wreck and swapping them over to test the result

Does this seem like the logical next step? Does anyone have any other opinions on the problem?

My car is a '93 R33 Series I GTS

In summer when the temperature is higher, the car starts fine, but the voltage still goes to around 8 volts.

Thanks... really want this sorted :)

Link to comment
https://www.sau.com.au/forums/topic/172314-engine-struggles-to-start-when-cold/
Share on other sites

Check your sparkplugs, running high-octaine fuel? got your car serviced recently?

8 volts is a bit low, on standard I think my car stays on like 12 volts or something. Also, have you checked your battery - enough charge in there - here's an inexpensive thing you could try - bring it to a mechanic, as him to fully charge up your battery for you - would cost around $20.00 or something, then see how you go. I've noticed with my car if I don't drive it enough, sometimes it will die down a bit.

Good luck.

My battery is brand new... found the most powerful one that would fit in the space

I tried putting in new spark plugs, but no change and I always use BP Ultimate 98RON

Didn't know about the oil though... I replaced the oil a few months back, can't remember the viscosity, but it was recomended to me by the mechanic for my car and its k's, so should be ok

Any other ideas? When I start it after its already been started once in the day, the voltage doesn't drop as far. It drops to about 10 volts. Its only the first start on a cold morning that it drops really low and struggles.

Thanks for the input so far guys :thumbsup:

I'm not too sure mate, I think it depends on how worn out your engine I think. The more worn/old it is, the thicker the oil should be. I don't know much about oils honestly.

Hopefully someone who does know will come and give their recommendations.

well boys i have had this same issue over the past 6 months, and it's a common thing, but belive me there is no sollution that i found.

I had replaced everything in the car, electrical that is, all new sensors, and test and so forht, you name it we tried it, eaven a new set of injectors, no good, then one day it came good, no idea how or why, but has been fine everysince. So bugga.

It's a pain in the ass to find too, seing as you only get one chance a day to diagnose it.

Personaly, i would start by cleaning your AFM. Also test or buy a new Engine temperature sensor, as this oftern plays havoc with the car. also put a new fuel fulter in the car and get the injecotrs cleaned, it may be that one is leaking a bit.

After that it's all trial and error.

I had new AAC valve, CAS, AFM, TP, ECu temp sensor, ECU, COILS, ect ect.

Thanks WogsRus... In my many hours of searching the forum I read heaps of things you had written... I will be trying all these things and hopefully don't struggle as much as you did :)

It may take a while to test each thing, because, as you said, you can only test what you tried once a day... I'll keep this post updated each weekend I try and make progress for all the others with the same problem... hopefully we get it sorted out ;)

If anyone else has any more insight, please let me know

Cheers

  DK1983 said:
hey adam

i have the same car and the same problem..with mine it clicks over first time but the rev's are very low like its going to die but after a second the rev;s jump up the correct idle...

interested to find out

Any chance you've got a fmic installed? I noticed that I had to blimp my throttle everytime I start the car in the mornings for it to get going after I installed my fmic. Not sure why it happened after the installation of the cooler, but I've had to. A little blimp of the throttle to get the car going isn't a big deal.

when you crank a car it's getting pretty close to a short circuit across the battery (you pull a LOT of amps) so the voltage will definitely drop - 10V would be a GOOD figure. 8V is probably normal.

maybe the cold start sensor is buggered or something? I assume there's a coolant temp sensor that's different to the one that runs your gauge....

i had the same probly on my r32 i cleaned acc valve ect but havent cleaned the one under the plenium yet... but ive found it struggles on cold mornings like you but lately ive been putting the siliencer in my exhaust in the morning when i start it and let it warm up bcoz my cars very loud.... and its always starts first time no worries with the siliencer in its quite funny... :D good luck who knows what the real problem is behind it but everyones car seems to do it.

I started my car the other day (r33) and as Idont drive it often it struggles in cold also.

It actually seemed like my coils as it sounded a bit like a rexy, did that for about 3 seconds and then ever again.

Must admit also there was a different smell coming out of the exhaust - bit like a kero smell rather than fuel!

weird.

I try and start it now once a day

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
    • I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I’ve been super cautious, did a lot of research, and took my time. I’ve driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times—no issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It’s not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test—belt isn’t too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it’s slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it’s just how it sits? I’m probably overthinking this, but since it’s my first time doing this on a NEO and the engine is forged, I really don’t want to mess anything up.   Also, I’m thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there’s a real difference between the two.   Any advice or reassurance would be much appreciated!
    • 40 grit sounds about right, to start. You make some decent cuts/damage in the coating with that, then rapdily scale up to maybe 80 and 120 for the bulk of the actual removal, then fine it off to 180 or 240 perhaps. No need to go any finer than that, and maybe no need to go even as fine as that. Wrap it on a big block and have at it. At least on the hub face.
    • Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes. Traction is going to be at a premium!
    • Hello,   My name if Frederick, i'm 30 years old and I live in Belgium, Europe! I used to have a Nissan 370z daily but since I got a company car I turned that into my seattime driftcar. About 3 years ago I also wanted something older with more feel, so I got an R32 GTST with an rb26 engine. I am now getting the rb built to have around 800hp and it's close to being finished. I'm very excited for how it will drive and how driveable it will be! Regards, Fred!
×
×
  • Create New...