Jump to content
SAU Community

Recommended Posts

Guest RedLineGTR

from what i have heard and personally use...also whats in your budget...i use shell helix 5-40 full syth like $45-50 for 5 litres. Also Motul in nice and you can go for redline, royal purple, if ya got the cash, but for a skyline oil changes every 5000k its abit expensive. I know a couple of people who use mobil 1, some people say it runs black really quickly after like 500km. You could also try Castrol they only make oils as compaired to some other companys.

Guest RedLineGTR
Originally posted by hippy

another question .. what is the cheapest high quality oil??  hmmm ... ??? ;)

Oils that a good for skylines do not go any cheaper than $50 for turbos...and i would not say thats cheap for a normal car non turbo lets say like a ford or something oils cost about $30 bucks or abit more depends on quality. About $50 is a good start.

Just because Mobil 1 goes black doesnt mean its not working. Viscosity is extremely important and probably more important than the brand of oil you choose. Engines are designed around having a particular thickness of oil running in their oil galleries, lifters etc. A thicker oil may not guarantee more protection because it cant move as quickly or get into the small areas in the same manner a thinner oil would.

Personally I use Mobil 1 Trisynthetic 10W/30 and i find it to be fantastic, even at $18 a litre. However the Motul do make a very good product.

Red17

Guest RedLineGTR

yep i'm aware that that it dosent mean that mobil 1 isnt working. Also about the Viscosity of the oil is important...Personal experience i tryed Castrol formulaR like $80 5 litres 10-60w seemed abit high but wanted to see if it made a diff. Changed the oil the oil pressure on the stock guage was really high, ( i know it it inaccurate some times but i was verry different compaired to usual) changed to my shell oil was abit better after that but wasent like how i wanted it. Flushed the engine out with a nulon product for oil. This is not recommended for older car. Wokred a treat and refilled with shell. Now the car is perfect normal pressure. Shell Helix ULtra 5-40. Filters were changed during each oil change.

The first number is the most important. You want it to be no higher than 10, so that the oil circulates quickly on startup. Fortunately almost all good synthetic oils are from 0W to 10W so you shouldn't have a problem there.

I am currently using Castrol Formula R 10W-60, and I think the second viscosity number is too high. My oil pressure is good (a little over halfway when warm), but I think the viscosity is overkill and is only hurting my power and economy. Therefore on my next change I am going to use 5W-30 and see how that goes.

The Castrol 10W-60 is still good stuff, and you might need to use it if your engine is a bit worn and burning/leaking a bit of oil. I'm not using any at all which is why I'm going to switch to the 5W-30, but as my engine wears out over time I will switch back to it. Hopefully not for another 100 000km or more :P

Oh, and definitely don't use mineral oil. Use a full synthetic (preferable) or a semi synth at the very least. Mineral oils break down too quickly. Change the oil every 5000km or sooner and you should be ok with a semi synth. My preference is still with a full synth though (still with 5000km oil dumps).

I've used both Mobil 1 0/40 and Motul 300V 15/50

Personally i find the Motul better - it has stayed clean the whole time (i am due for an oil change now), has not used a drop and still feels fantastic. Mobil 1 is excellent too, but i found it discoloured a little quicker (discoloration = wear?) and seemed to 'go off' or feel slacker quicker. But like someone said above, a change every 5000k and either one of these oils look abit expensive - for the Motul i got 4L for 70 bucks!

Oil staying clean means that it is not doing its job properly. You want your oil to go dark fairly quickly because that means it is absorbing all the crap that your engine produces. If it's not in your oil it's grinding away at the internals of your engine!

I look at the very thin edges of the oil on the dipstick to tell if other cars' oils have become saturated with contaminants or not. On my cars it's always got a slight golden hue on the edge. Some cars overdue for a change are black right to the edge. While you still have a bit of gold in it that means it's still got enough cleaning properties in it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...