Jump to content
SAU Community

Volk Te37 18x9.5 Suit Gtr

RPMGTR
 Share

Recommended Posts

RPMGTR Community Regular

RPMGTR

Posted
Posted (edited)

Set of 4 Volk Racing TE37 18 x 9.5 +12offset in white suit GTR

Good condition, ready to pick up now.

$2500

First to pick up with cash in hand gets these.

No deposits, bank transfers, trades, iou's, notes from your mum etc...

You don't own them till you have collected them.

cheers

Now SOLD.. Thanks

post-4150-1182558803_thumb.jpg

Edited by RPMGTR
Link to comment
https://www.sau.com.au/forums/topic/173862-volk-te37-18x95-suit-gtr/
Share on other sites
Zardos Community Regular

Zardos

Posted
Posted
Set of 4 Volk Racing TE37 18 x 9.5 +12offset in white suit GTR

Good condition, ready to pick up now.

$2500

First to pick up with cash in hand gets these.

No deposits, bank transfers, trades, iou's, notes from your mum etc...

You don't own them till you have collected them.

cheers

Will the off set suit a R32 GTR?

Sol32 Community Regular

Sol32

Posted
Posted
Will the off set suit a R32 GTR?

+22 is a better suited offset to R32... these will stick out further than those. Guess the only way you'll know for sure is a test fit...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • Murray_Calavera
      Exhaust silencers/varex exhausts

      By Murray_Calavera · Posted

      They also make them with the motor mounted on the side 
    • GTSBoy
      Blue/grey smoke after idle

      By GTSBoy · Posted

      Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...