Jump to content
SAU Community

Headlights Fogging Up! Just Paid For New Ones! Still

4drftn

By 4drftn,
in General Maintenance

 Share

Recommended Posts

Spunky Munky Grand Master

Spunky Munky

Posted
Posted
Drill a small hole into it... on the plastic somewhere thats not too visible.

Are you nuts??

Look, to make sure they do not fog up - when you install the lights in the first place, choose a warm hot day - get a soft cloth and clear out all gease, dirt and dust from the lights arch - now install the lights, then make sure you seal it up real good - now, purchase some cleaning lotion at Autobarne (ask for something that is made to clean up plastics etc) - rub away at the front of the lights - it will take a while, but work hard on them and they will shine.... now, just clean them every 2-3 months and you should be fine... my lights look brand new... because I do the above...

Good luck... don't drill any holes... the guy is nuts...drill holes and water will leak in, air will past through it etc and fog will build up even more...

good luck.

typevu Grand Master

typevu

Posted
Posted
Are you nuts??

Good luck... don't drill any holes... the guy is nuts...drill holes and water will leak in, air will past through it etc and fog will build up even more...

Hahahaha says the person wanted to import a Calsonic Skyline to use as a road car :laughing-smiley-014:

Drilling a hole will allow air to flow in and out and not fog up - Its like driving during a cold rainy day and the windows start fogging up - wind down the window and fog goes away.

Spunky Munky Grand Master

Spunky Munky

Posted
Posted
nudge nudge

Sorry bro.... what you need is a thing called "clear seal" it's a white, see-through gel-like glue... must be bought at Bunnings or something... this did it for me... but when you seal it up, make sure you only use small dosages...

Good luck mate... let me know how you go..

Spunky Munky Grand Master

Spunky Munky

Posted
Posted (edited)
Hahahaha says the person wanted to import a Calsonic Skyline to use as a road car :laughing-smiley-014:

Drilling a hole will allow air to flow in and out and not fog up - Its like driving during a cold rainy day and the windows start fogging up - wind down the window and fog goes away.

Viet-tastic hommie... yep, and I still want to import an Calsonic Skyline... who wouldn't, right?

Laterz hommie... the the yellow and 3 red stripes represent yo! :thumbsup:

PS: with the drilling thing - I still think it's not necessary.. why would you want a hole in your headlights holder when you can seal it up nicely.?

Edited by Spunky Munky
OZ_Pomy Rising Star

OZ_Pomy

Posted
Posted
Viet-tastic hommie... yep, and I still want to import an Calsonic Skyline... who wouldn't, right?

Laterz hommie... the the yellow and 3 red stripes represent yo! :P

PS: with the drilling thing - I still think it's not necessary.. why would you want a hole in your headlights holder when you can seal it up nicely.?

You would want to drill the hole in the light because it works how can you say the other guy is nuts have you tryed this before or not? And you take the light out drill in the bottom of it then put the light back in that way you wont even notice the hole.

Spunky Munky Grand Master

Spunky Munky

Posted
Posted
You would want to drill the hole in the light because it works how can you say the other guy is nuts have you tryed this before or not? And you take the light out drill in the bottom of it then put the light back in that way you wont even notice the hole.

If that's the case, then I guess you do have a point - yeah, I've never tried it... but drilling holes is the last resort IMO... but hey, if it works then up to the owner of the vehicle. :rolleyes:

Cheers.

RANDY Veteran

RANDY

Posted
Posted

Soo.... fogging up? In which way? Condensation, or the hazy plastic problem that some R33's seem to have?

I have to get out the ol' plastic polishing cream and buff my headlights like crazy every couple of months to get them clear again. It sure isn't condensation on the inside, is this the same problem as you have?

If it's condensation, then I can see how the "hole-drilling" would help but if it's the magical "I bought it from Japan and now the plastic hates Australian climates" problem, i'm keen to hear more suggestions!

Boss-zilla Mentor

Boss-zilla

Posted
Posted

If your talking about condensation (looks to be fogging up on the inside after rain/wash) like the other guys said, drill a SMALL hole (or several) in the bottom of the lense this will fix it.

If the lights are going a yellow colour after a while get some plastic polish or look in the FYI/DYI are, i think there is a write up in there for a once off fix.

SMOKEYV35 Mentor

SMOKEYV35

Posted
Posted
If your talking about condensation (looks to be fogging up on the inside after rain/wash) like the other guys said, drill a SMALL hole (or several) in the bottom of the lense this will fix it.

If the lights are going a yellow colour after a while get some plastic polish or look in the FYI/DYI are, i think there is a write up in there for a once off fix.

i wouldnt drill if i were you. i had this problem in my headlights, it was frustrating as all hell. it happened whenever i washed the car or left it in the rain. basically the water is leaking in somewhere, contained in a warmed environment (like a greenhouse inside the headlight), and condensation results.

the reality is that it will continue to happen, because water always gets into a leak point whenver its around. drilling a hole wont do anything, its just a bandaid. it will allow some of the water to drain over time, but not all. it will also allow dust in, so that when the light is damp, road dust will find its way in (just like water, its very sneaky), it wil cloud the headlight over time and make it look shit. no amount of plastic polish will help, cos the grime will be on the inside, not the outside.

only way to truly fix it is to take the headlight apart, clean it thoroughly, and reseal it. there is a guide on this forum about how to seperate the lights using an oven. resealing them, the best stuff to use is sikaflex, comes in a black tube, from any auto/hardware store. i did it, it was messy and time consuming, but the end result is 100%

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jacobzking
      Feedback on these “rebuilt” Nismo injectors

      By jacobzking · Posted

      Thank you!
    • Duncan
      Feedback on these “rebuilt” Nismo injectors

      By Duncan · Posted

      I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • jacobzking
      Feedback on these “rebuilt” Nismo injectors

      By jacobzking · Posted

      I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
×
×
  • Create New...