Jump to content
SAU Community

Recommended Posts

hi,

just wondering what you peeps out there do to get rid of any annoying interior squeaks and noises?

I have a couple, and firstly, find them hard to pin point and second have no idea how to get rid of them.

I have an R34 and the area around the top guage cluster has a bit of a creak to it, not sure where exactly.

just wondering if anyone has any processes they use to elimante unwanted noises, or if anyone knows of any common causes for the squeaks, etc...

cheers

yeah its a bitch aye. Try taking off the interiour panel and putting a really thin sheet of foam/sound deadening under it. Or maybe a drop of silicone over the metal clips so they dont vibrate

I always try and push on everything at different points while it's rattling.. see if I can narrow it down to the bit of plastic, panel, etc that is moving around. Often it's just a screw undone..

After I've found it I'll shove a bit of folded paper in there, or obviously replace the screw.. generally I'm pretty successful at getting rid of them on most of the cars I've had.

yeh bro ive got an r34 n somewhere in the back seats where the plastic overhead things are theres a major squeak noise everytime i go over bumps..n it also comes n goes..

some days its nice n quiet and some days u just wanna rip the interior out

whenever I turn up the stereo my splits make an annoying vibration noise in the rear parcel shelf.

Not sure if it's the plastic brackets or the speakers, but it's very annoying, anybody got any tips?

^ so Porshe's come with felt tape from the factory?

felt tape.... silicone stuff... foam deadening.... paper :) - some good things in here :blush:

i've got one "creak" on my drivers door, in the cloth/fabric section (under the window) how would i get behind there? take the whole door trim off? i've NEVER dismantled any trim before, is it fairly easy to do?

it is. just remember to go slow the first time, be careful and make sure you are applying force in the right spots. once you've done it once it becomes a lot easier. try to be even in you pulling too. if you are bending things that arent meant to bend, you are gonna do damage.

EDIT: re reading that bit of advice, i rekon that it can be applied in a totally different "first time" situation too :D:(

That's pretty true. I don't remember or wouldn't have noticed on our old 320i, 528i. But the 530i i believe is squeak free, the 335i has a little one that's popped up (and considering it's less than half a year old, that's not too good) but the suspension is much harder. The 318i has a few noises.

i think the stiffness of the suspension plays a huge part. The stock R34 suspension i find is actually quite stiff, or the shocks are crap, or something, i dunno.

I have an annoying creak in the passenger side inner rear trim, the one that runs along the top of the rear window and down...

Ive tried squeezing silicon filler in there, and still no dice.. If I knew how to remove the bloody thing I could get in there and take care of it properly! Anyone happen to know how these panels come off?

my door tirm has the sounds..

if i press down or put my arm on the door trim while im driving it crys out like a pig...

same as passenger side door trim..

and also if i press down the back seats, it makes metal scripping sounds... i think its because of bushes... anyway...

i have to dissemble those trims and put somethings between connections.... i hate that noise....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...