Jump to content
SAU Community

Recommended Posts

Checked another Autobarn. They have it for $34.99 per 500ml bottle. Sounds pricey. Is that about right? Castrol dot 4 is only $10.

I get it from autobarn in Moorabbin and pay about that.

And if you think the $34odd (for 500ml) dollars is expensive try buying the castrol racing brake fluid....1 litre for about the $120 mark!!

Yeah price is right, good stuff though. Worst bit is I have an amost full bottle sitting in the garage. I had to open it as 1 wasn't enough when I was bleeding the brakes. Apparently its not good to leave it sitting round even though it's done up tight. Anyone know how true this is?

How longs it been sitting there?

I cant see how it sitting there would effect it, I mean it may sit on the shelves for months b4 sold.

Unless its once its been opened then its "shelf life" begins?

But yeah, 100% Autobarn should have it, if they dont ask them to call neighbouring stores for ya so u can swing past there n get.

I know the Scumshine store has plenty of them. :domokun:

Motorbike shops are the go :) I got it there last time and they always tend to have it. Where abouts are you?

Edit - Just re-read your post. Check the Motorbike shops down on Burwood Hwy in FTG near Safeway :)

Yep Try The motorbike shops there.. that's where i get mine from. The one with the Jetski shop downstairs... Don't think i was paying that much, think it was $25 or something, maybe 30...

Yeah price is right, good stuff though. Worst bit is I have an amost full bottle sitting in the garage. I had to open it as 1 wasn't enough when I was bleeding the brakes. Apparently its not good to leave it sitting round even though it's done up tight. Anyone know how true this is?

Yeah I think the reason is the moisture in the air gets into it which is bad. But think about it - what about the fluid in your master cyl that is sitting there with a lid on it (probably not as air tight as the lid on the RBF600 bottle).... so yeah i don't belive it. I've got a half bottle sitting in my toolbox draw with the lid really tight...

Yeah I think the reason is the moisture in the air gets into it which is bad. But think about it - what about the fluid in your master cyl that is sitting there with a lid on it (probably not as air tight as the lid on the RBF600 bottle).... so yeah i don't belive it. I've got a half bottle sitting in my toolbox draw with the lid really tight...

Yep spot on ferni....as far as I know as you move up the dot rating (dot 4 - dot 5 - dot 5.1 etc) the brake fluid becomes more succeptable to absorbing water and as we know the higher the water content in the fluid the lower the boilng point etc which in turn means a dodgier brake pedal. This is why dot 4 brake fluid in most everyday cars don't need to be replaced as often as dot 5.1 fluid.

That said as long as you don't leave the container open for extended periods and the cap is on tight it should last a while.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...