Jump to content
SAU Community

Recommended Posts

Folks,

I got a 3 inch nismo catback (bought it off someone from the forum)bolted on yesterday to go along with the 3inch catco hi flow cat I already had and didnt seem to notice a rise in the power at all. Thought the power was averaged much more smoothly across the revs range I quite didnt feel the increase in power as I had expected to. Am still running the stock dump and front pipe.

Was wondering if this was normal or was should I be seeing a noticeable gain ? Does running the stock dump have such a major role to play in this?

Cheers guys

PS anyone looking for a quiet exhaust though this is what I'd recommend. Its just a tad louder than the stocko and what exactly what I was after

post-36886-1183780392_thumb.jpg

it would be quite normal, it may increase spool up times, but is better noticable with the rest of the exhaust complete, keep in mind as well a highflow filter being pod or panel replacement will also help if it hasnt been done yet, Also the boost mod, you may still be running off the standard boost solenoid, its hard to say maybe help us out list what else has been done to it

Cheers

A

by just completing the last half of the exhaust wont actually increase the power that much

  • 2 weeks later...

paid 600+ 50 postage to sydney from adelaide. But am now bloody pleased with its performance. Looking to finish the exhaust off with the JJR split dump soon. then its fmic, pfc and injectors, fuel pump bank balance crashing time........ :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mainly being afraid of breaking something on something i've poured so much money into haha
    • Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
×
×
  • Create New...