Jump to content
SAU Community

Wanted/needed Help!

Lukaz

By Lukaz,
in Victoria

 Share

Recommended Posts

Lukaz Community Regular

Lukaz

Posted
Posted

Ok guys I have no idea who I can go to about this bout I figure if I post this thread someone will atleast give me an idea.

I need to re wire my boot release/petrol cap cable as mine has snapped, and also "maybe" redo my bonnet release cable too as it feels like that could be going soon.

If anyone has an experience with this PLLEEASSEE reply to this thread.

Im working flat out at the moment and don't have much time to pull the everything out to find out exactly the parts I need.

So basically im askin for advice and possibly if someone would be kind enough to acompany me to a wrecked skyline or something to show me which parts Id need to take etc.

Car is an R32.

Link to comment
https://www.sau.com.au/forums/topic/176108-wantedneeded-help/
Share on other sites
Lukaz Community Regular

Lukaz

Posted
  • Author
Posted

Posted in maintance a few months ago, got no replys, I thought if I posted it here id have a better chance of catching someone local who could help out.

Cheers Mav, Ive had a look under the carpet, My biggest concern is wrecking a mounting bracket or something, My boot is flakey as it is (Someone tryed to break into it by wedging a screw driver under the boot lid, f**ked the lock), so I was hoping Someone with some knowledge of it could help me just cane threw it as aposed to me doin trial and error and probably f**king something up worse.

Infact thats how I made the boot release worse in the first place haha, the petrol cap was still working fine untill I had a shot at fixing it and now its f**ked too.

R TUNE Mentor

R TUNE

Posted
Posted

hey mate,

i had a similer problemin my r31 were my boot release would not work (wasn't the cable in the end but changed it any way).

you will need the following,

one boot release cable (u'rs broke right)

you will need to located were the cable runs, my was from the driver's seat up the side of the car in to the boot and followed around till the boot lock.

i did have to remove the rear seats and front seat to get under the carpet.

i then removed the cable its quite easy. then replaced the cable in the same way i pulled it out.

i then adjusted the boot lock (the bottom one) to get the boot to work properly and site right.

all up too about 1 hour in total.

should be fairly the same as the r31.

hope this helps

Lukaz Community Regular

Lukaz

Posted
  • Author
Posted

Im pretty sure it just from wear over time,

Redline - Thanks heaps for the help, I was figuring that, I dunno with R31s, but the release cable controls both the boot and petrol cap.

You rekon there is any place I can source one of these out other than waitin for a wrecked R32 to pop up?

R TUNE Mentor

R TUNE

Posted
Posted

yea thats the same for r31 you push down on the leaver and it opens the fuel flap and pull up to open the boot.

your best bet would be a wrecker that wrecks r32 or look in the for sale section here.

you could even try and r31 (common as s at wreckers or being wrecked on r31skylineclub.com) and see if it fits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Starting again

      By GTSBoy · Posted

      This is the GTR fuel pump. Yellow shows 12V, orange shows earth. The ECU provides the earth to activate the fuel pump relay. The ECU side of teh relay will pull low when the ECU activates. This is the RB20 fuel pump. Almost the same, but a little simpler. You can see I indicated (above) where the 12V line goes down to the RB20 diagram on the overall diagram, whch shows both RB26 and RB20. This is where I show it coming in on the RB20 diagram below. You can see that the dropping resistor is handled differently. When the fuel pump control is not providing earth to the pump, the pump earths through the dropping resistor and thus runs at lower voltage (some is wasted over the resistor) and runs slower. I showed that "not 12V and not quite earth" portion of the wiring in a paler orange. The rest of the wiring that I did not colour on that little section below the pump would be orange when the fuel pump coontroller is providing earth. This drop is handled inside the fuel pump controller in the GTR. Regardless, you can see where 12V is supposed to be, where earth is supposed to be. The key on prime is via the ECU providing the pump for only a few seconds the switching off. You should be able to see that happen.
    • Duncan
      Starting again

      By Duncan · Posted

      Yeah so when you turn key to IGN the fuel pump should run for a few seconds. If you find the fuel pump relay (and have a multimeter, and a second person) to can check the relay inputs.  One trigger pin should be either fully earthed  The other trigger pin should get 12v from the ECU for say 3 seconds when you turn key to IGN, and at all times that key is at START (note, I said this from memory, it may be the other way around, ie one pin always has IGN 12v and the earth has continuity to earth when you turn the key) One Pin should have a good battery voltage The last pin goes to the fuel pump + Also note that if the power to the relay is good, and the relay is working, it is worth checking the pump has a good earth too. There is a computer in the standard system that increases the earth resistance to slow down the pump when not required, pretty old school and it may have failed
    • Ozdavroz
      Starting again

      By Ozdavroz · Posted

      All this talk about fuel and fancy ECUs, meanwhile my poor old R32 has neither.... When the ignition is turned on, should there be power running o the fuel pump constantly or just for the few seconds it usually takes to prime the pump? About to go have another look at it, have watched some YouTube vids on how to use a  multimeter and looked at some wiring diagrams but really have NFI what I'm looking for because electricity is invisible  
    • GTSBoy
      R32 Nostalgia

      By GTSBoy · Posted

      Yuh....but weren't all the supertourers, except maybe the Audis, FWD? I don't recall any of the others being AWD.
    • Duncan
      R32 Nostalgia

      By Duncan · Posted

      They ran them in Oz Super Tourers too https://www.supertouringregister.com/register/vehicle/212/ (I'm so old I remember racing with Matthew Fox) They ran them in Oz Super Tourers too https://www.supertouringregister.com/register/vehicle/212/ (I'm so old I remember racing with Matthew Fox)
×
×
  • Create New...