Jump to content
SAU Community

SAU Caps & Beanies... just made a deal, any1 want one?


Recommended Posts

  • Replies 246
  • Created
  • Last Reply

Top Posters In This Topic

ok, i upgraded finally to poser 5, and to my surprise there's a new updated cap model in it!!! :)

that means good quality cap renders... here are a couple I did from some of the logo designs I made. Now I can make your design instructions into pictures, so fire away guys. I'll need good desciptions... which logo, where, what orientation, what angle etc etc.

here's one design to get yas started:

cap1.jpg

cap2.jpg

Hey i think that that last design is choice, What design is it going to be for the beanie, any desisions?? not that it matters really though. Could you have it ready for this weekend though as am heading down to the snow. hehehe

Put SAU in white in the middle with the after burner tail lights on either side, on an all black cap. on the back (and I know everyone will say I'm a nerd) the url

Beanie just have the sam SAU logo as the cap.

my 2c

Cheers.

Guest DIESEL

Dude the design is sick! The monogram block with tail lights looks good. ASnd with the skylines.com wrap around the base or rear would compliment well. Put me down for 1x white cap, 1x black beanie, cheers. Top work on the organising Funky.

the peak will be the same colour, I just couldn't get a render with the same colour that looked clear, it jus looked like a massive black blob

i'll take a white one, red one and black one of the bottom one but put the URL on the side or back of it.

Put me down for a white skully too...

altho if u could make the midlle ones logo bigger so it goes over more of the heat it would look even better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I chose a bad time to buy, at the time there was no gtst's for sale in NSW and my options were qld, vic, or sa and not the greatest examples or too far out of my budget. Ended up picking this one from adelaide sight unseen and got a bit stitched up as you could expect but i dont fully regret it, its just a shame people cant be more transparent in this day and age.
    • IMO just buy a whole R33 transmission and swap the whole thing. Use a palm nailer/air hammer with a roll pin punch to drive the shifter rod end roll pins out. The rod end is discontinued so don't break it. Use gasket dressing on the OEM paper gasket instead of RTV. I personally would not pry on the shifter cover tabs, I broke one trying that instead of just smacking the side with a dead blow rubber mallet to shock it loose from the RTV the last mechanic applied. If you can't get the flanges totally clean and free of any residual RTV and/or you might have a gap that is bigger than it should due to flange damage use RTV on that surface instead of the OEM specced anaerobic sealer. Anaerobic sealer is most likely the right sealant for the job, it's just too easy to mess it up with too large a gap or bad surface prep/roughness seemingly. If you do rebuild what you have it's for a whole gearset that can take high torque. Don't bother with OEM at that point.
    • Little hose. Big hose. They're all waiting to kill the engine.
    • Nice ride, hard to find these days!
    • Full e85 barrell stuff real world for reference if it helps as Ive pushed 2 x sets injectors to limit Above mentioned Bosch 1480cc run on 4 bar base to the apparent 1650cc on rb2.7 yielded 912hp / 684  kw  at 92% duty on hub dyno ID1700's - RB 2.8 ...1015hp / 760 kw at 87% duty - hubber dyno + shown off data on track my opinion IF you change injectors just go bigger than you think you need the modern/ good larger ones run just fine if tuned properly even if way bigger than required even on streeters  
×
×
  • Create New...