Jump to content
SAU Community

About To Do Timing Belt For First Time :s

cosworth1971

By cosworth1971,
in General Maintenance

 Share

Recommended Posts

cosworth1971 Community Regular

cosworth1971

Posted
Posted

Never done it before on a skyline96 gtst

but is the hardest bit the pulley or something else?

just worried the cams may move when i take the belt off( so do i need to hold them in place?)

due to spring preasure?

ive also been quoted under 50$ for a water pump from auto pro but thought water pumps were dear for my car?

axe s Experienced

axe s

Posted
Posted
Never done it before on a skyline96 gtst

but is the hardest bit the pulley or something else?

just worried the cams may move when i take the belt off( so do i need to hold them in place?)

due to spring preasure?

ive also been quoted under 50$ for a water pump from auto pro but thought water pumps were dear for my car?

i'd be double checking part numbers... that doesn't sound right, mine cost $130 from tweakit (probably not the cheapest but can't be that far off) get a manual if it's ur first time (can buy a CD version on ebay for like $15)

But u just have turn your crank to no.1 TDC then your cams should line up with your 0 degree mark there is one on each cam and i think one on the crank (can't remember)

cosworth1971 Community Regular

cosworth1971

Posted
  • Author
Posted
i'd be double checking part numbers... that doesn't sound right, mine cost $130 from tweakit (probably not the cheapest but can't be that far off) get a manual if it's ur first time (can buy a CD version on ebay for like $15)

But u just have turn your crank to no.1 TDC then your cams should line up with your 0 degree mark there is one on each cam and i think one on the crank (can't remember)

I got the manaul for free ,that guy who sells them is a scam! i know he got his at the same place :) it on the web for free

colgf Enthusiast

colgf

Posted
Posted

There is an excellent thread on the STAGEA forum. Covers all the steps to change the timing belt on a RB26 motor , Yes , the crank pulley nut is the hardest thing to undo , its done up to 650ft/lb torque , you may need to make up a pulley lock tool to hold the pulley still while you crack the nut.

cosworth1971 Community Regular

cosworth1971

Posted
  • Author
Posted
There is an excellent thread on the STAGEA forum. Covers all the steps to change the timing belt on a RB26 motor , Yes , the crank pulley nut is the hardest thing to undo , its done up to 650ft/lb torque , you may need to make up a pulley lock tool to hold the pulley still while you crack the nut.

650ft torque do you need a 10 ft extension bar for that or does metal atoms seperate at that force?

are you serious? no torque wrenches will be able to do it up again? i was thinking is it ment to be 165ft pounds?

axe s Experienced

axe s

Posted
Posted
650ft torque do you need a 10 ft extension bar for that or does metal atoms seperate at that force?

are you serious? no torque wrenches will be able to do it up again? i was thinking is it ment to be 165ft pounds?

i don't know what it actually is, but i can tell you it is far,King tight... took me a while to get mine off...

make sure u lock ur flywheel before attempting to undo it..

axe s Experienced

axe s

Posted
Posted
isn't it hard to actuall 'pull' the harmonic balancer off as well? ie need a proper puller?

yeh, only costs $20 from supercheap can get cheaper but they didn't have small enough bolts to fit factory Harmonic balancer...

Duncan Grand Master

Duncan

Posted
Posted

water pumps from an rb30 are dirt cheap - be careful they have less blades that a standard one so they pump less water - the rb30 ones are kind of half way between standard and the n1 water pumps.

I thought the balancer bolt was only 450lb/ft but yes still bloody tight :).

Make sure if you buy bolts for the balancer puller that you get high tensile, at least 8.8 and preferably 12. If the bolts snap you are in a world of trouble getting the balancer off.

crofte Collaborator

crofte

Posted
Posted

Make sure you replace tention spring correctly behind pully as it is ecentric. spring must clip in behind dowel to give correct tention on belt. Get onto VACC for instruction manual for rb25det it will help you a great deal. :)

FOG35 Collaborator

FOG35

Posted
Posted
yeh, only costs $20 from supercheap can get cheaper but they didn't have small enough bolts to fit factory Harmonic balancer...

You actually dont need to buy the bolts because the bolts that hold the cam cover on are the correct size. I did this in mine a few months ago however was a rb20 but i would assume the rb25 would be the same.

And I paid $70 for my water pump from repco.

  • 2 weeks later...
VSPEC-33 Community Regular

VSPEC-33

Posted
Posted
water pumps from an rb30 are dirt cheap - be careful they have less blades that a standard one so they pump less water - the rb30 ones are kind of half way between standard and the n1 water pumps.

I thought the balancer bolt was only 450lb/ft but yes still bloody tight :pirate:.

Make sure if you buy bolts for the balancer puller that you get high tensile, at least 8.8 and preferably 12. If the bolts snap you are in a world of trouble getting the balancer off.

Just buy a new crank bolt from Nissan, the one for my car was only about 10 bucks and you know its going to hold up.

Damn the old bolt was a bitch to get off. 1 metre breaker bar: no good, crank over engine with extention bar under chassis rail: no use. In the end had to use a trucksize rattle gun, which meant radiator and condensor out just to fit the gun down there!

And i went a genuine Holden VL waterpump because it has the no. of blades between std and N1, the car has never overheated. It has a Nissan part number anyway, most likely the same as an R31 RB30E, works perfectly and alot cheaper.

foznice Veteran

foznice

Posted
Posted

I reccomend taking the radiator out. Makes removing the harmonic balancer alot easier and it will probably save your knuckles from a good skinning.

You can line up a torsion bar so that it's up against one of the rad supports or the ground even, and use the starter motor when cracking the big mofo bolt for the harmonic balancer... some people don't like to do that though..

As someone said, just line of TDC 1, and everything should be fine. Just check the markings about 50 trillion times before you put it all back together.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Got just the wing painted and fitted up to the existing boot. Big visual change and about time after having a GTR wing sitting in the shed since 2018 Headed up to Mallala with a quick obligatory stop in at Boliver OTR Oil control mods seems to have worked. I checked the catch can after session 1 and there was a dribble of water/e85 with barely any oil in it. After session 2 and 3 there was almost nothing and I stopped checking after that. so either great success or catastrophic failure/block of the external breather The GTR wing made a noticeable difference in the 160-185km/h sweepers. It was a very hot day for the cars at over 33C but the previously done cooling upgrade/ducting/water sprayers meant I never saw over 60C intake, 105C water and 100C oil and temps would drop back down very quickly once I shut it down. AD09's are a decent tyre but certainly and expectedly a step down when compared the the CR-S/AR-1 I have had on the car for years of track days. The handling characteristics of my car which I often describe using the Tony Hawks Pro Skater balance mechanic where either side of the center is understeer/oversteer was much more pronounced with no "green/safe" zone in the middle. However, imo it steers well/easily during oversteer largely thanks to the custom ACOSTAL front end. Enjoy a loose lap POV with my mate giggling away as a passenger.   Group photo for Peer Pressure Racing made it back home and gave it a wash Overall a great success compared to my previous two track days where i cooked the Starlets motor and blew up the new diff in the R32  
    • PranK
      R32 GTR (USA-Alabama) KG1 1990

      By PranK · Posted

      Nice. I'm looking forward to the updates!
    • Templim
      AC not coming from top vents

      By Templim · Posted

      Ayooo, been a while mates. I have a s2 r33 gtst and air stopped coming out of all the top vents.   My car has always made an actuator gear noise when turning the car on but that's a different issue I think? Did searches and am at process of thinking it's an actuator or some type of motor? I see a few different actuators and don't know which one. Would be nice to know if it was the one that's under the steering wheel so the dash doesn't need to come out.
    • sunsetR33
      Custom titanium intake

      By sunsetR33 · Posted

      Hi, just checking. Did you get this stuff made by Vspec Performance and at what price roughly? Looking into (sometime later) also getting such a intake kit, and Trust as well as HKS don't make a full set like this anymore.
×
×
  • Create New...