Jump to content
SAU Community

V35 Rims With Tyres

predator
 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

V35 rims off what I think is an V35 coupe.

Front: 7.5" Offset: 33

Rear: 8", Offset: 30

Tyres on rear are 215/55 Nanganks. Front are 245/45 BF Goodrich (cost me $220 each new). Tread wear is about 95% even throughout

As you can see, they fill the guards fairly well on an R32. To be honest, I reckon they might look more suited on a more modern car such as R33 or R34. Nice solid wheels in VGC, with no gutter rash

Nice cheap way to get a unique look for your Skyline, and don't think I have seen these on another r32/r33/r34 yet.

Price: $500 not negotiable, pickup only

Note on R32 - I don't recommend keeping the high profile 215/55 rear tyres if your skyline is lowered more than 30mm as they will scrub if you drive hard. R33 or r34 should be not an issue.

v35rims01.jpg

v35rims02.jpg

Link to comment
https://www.sau.com.au/forums/topic/176495-v35-rims-with-tyres/
Share on other sites
  • 2 months later...
SevenAngryPenguins Proficient

SevenAngryPenguins

Posted
Posted

did you end up selling these wheels?? I have some on my 33 and i just wrecked one of mine on the back on a big rock so might be interested a bit down the track if you still have them of course

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Drive By Wire Conversion options

      By Watermouse · Posted

      I recently got their dbw 74mm throttle body and pedal kit. It is sensational quality especially the wiring harnesses. Unfortunately I can’t answer u about the fitment to stock inlet manifold as I’m going Rahjab Racing forward plenum. Only one thing to be careful of is understand u have to pay gst and import fees if your purchase is over $1,000 in one shipment.
    • pogman
      George's R33 GTST build

      By pogman · Posted

      yeah i agree paint match stops it from standing out so much, oh that's actually really good to know i was wondering if it would help with air flow now actually having an outlet in the bonnet. Will have to focus on ducting into and out of the radiator now to make the most of it.
    • The Bogan
      George's R33 GTST build

      By The Bogan · Posted

      I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • shortyboy
      Drive By Wire Conversion options

      By shortyboy · Posted

      Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • pogman
      George's R33 GTST build

      By pogman · Posted

      small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
×
×
  • Create New...