Jump to content
SAU Community

Recommended Posts

Pre-meet for north and east side peoples who are comeing on the sep 9 GOR cruise or any body else who wonts to come, open to all

the last one i orgonised we had about 10 cars which looked awsome.

DATE: 9-9-07

TIME: 08.00H meet for 08-45H leave

LOCATION: Preston Mcdonalds cnr of bell st and st georges rd

WERE TO: little river BP for main GOR cruise.

WHOS COMEING:

danial (cheeze)

dilmah

assyrian4evaa

ashneel

unknown:

Brentt (redliningr31skyline)

post-32868-1184379858_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/176497-gor-run-pre-meet/
Share on other sites

yeh ill be there. Main gor cruise meet time is 9:30 for 10:30 departure, so brent make the leave time 8:45.

oh yeh and the maccas is actually on the corner of bell st and st. georges rd, not up further as stated.

Edited by cheez
  • 3 weeks later...
Pre-meet for north and east side peoples who are comeing on the sep 2nd GOR cruise or any body else who wonts to come, open to all

the last one i orgonised we had about 10 cars which looked awsome.

DATE: 9-8-07

TIME: 08.00H meet for 08-45H leave

LOCATION: Preston Mcdonalds cnr of bell st and st georges rd

WERE TO: little river BP for main GOR cruise.

WHOS COMEING:

Brentt (redliningr31skyline)

danial (cheeze)

Guys.. Guys Guys

I think the reason there are only 2 names on your list is coz

You say you are heading down on Thursday the 9th of August..9-8.07

And before that you say Thursday the 2nd of August..2-8-07....

I think it woukd be better run on a weekend....My 2 cents

brent can we have a poll in this forum, i have had suggestions for other meet locations, so could you set up a poll for either bell st maccas or Kmart in campbellfield which is right next to the ring road on ramp.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...