Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Err how is that possible? Is your exhaust connected to your intercooler? :(
:laughing-smiley-014:

Luckily it didn't go the other way and end up in your sump hey? or even worse, in the flux capacitor.

ok ok... know how a turbo works? obviously not you keyboard monkeys...

when your ceramic turbo wheels blow at 6000rpm, where do the peices go? out the exhaust AND ALSO through your intercooler..

so who said they were connected?

fully sick yea??

god some people just need to grow the f*k up and read between the lines :(

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/page/3/#findComment-3265020
Share on other sites

assuming you drive a commonhore t like me...

well if its an s1 it would be bits of steel in your cooler core + through engy eventually out the exhuast.. if they are small enough and after they have scored shit pretty well... like sand.

if s2 nylon.. same deal.. potentially less damage inside if it makes it through your coolers core...

ceramic exhuast side only....

never heard the flutter out of my car... high or low throttle... dunno... every time i think fluter i think of the dumb 200sx driving twat indian near me who always wants to run... hes been pulled over for trying to push me into a race... he still trys...

best part.. was @ wsid once with his 20" wide 3" thick steel rimmed sr with his mates trying to show everyone up...

not only did i beet him but so did a drunk smartass in a combi.. .. was awsome for a laugh

200sx that pulls late 14s.. MUAHAHHahahahahaha what a dumb twat...

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/page/3/#findComment-3265300
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Kaizo Industries put a VIN plate over where the Nissan plate would go. It was part of how they broke the law and attracted feds going after them.
    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
×
×
  • Create New...