Jump to content
SAU Community

Recommended Posts

I noticed that the boot was leaking in my Series I R33 GTS25t..there was water in the spare tyre well and also down the side where the jack is kept (left hand side when standing behind the car) but the right had side was pretty much dry..is there any common places that it leaks that i can block up with silicone or something? Any ideas? Cheers.

Link to comment
https://www.sau.com.au/forums/topic/177167-r33-boot-leaking/
Share on other sites

I had this same thing. Was coming in the tail lights. Is there moisture build up in you lights? It will show up most inyou indicators. You can take it off and reseal it. Just don't get the sealant on your paint. Its a real pain to get off

Its definitly not from the spoiler, boot seal and theres no rust at the bottom of the window so it cant be from there..it may be the tail lights because i can see sort of "water marks" where water has been and left trails and dried up at the back of the lights..i might check the window wiper too..how hard is it to change the seal on the window wiper?

I've got an R32 sedan and I found about 5+litres of water in the jack area of my boot :laugh:

I have no idea as to where it's come from. The boot area is all dry, it's just the jack area and the other side.

It's been about a week since I sucked out all the water and it's rained quite a lot down here in Melbourne. I might check later today to see how much water is in there now.

I've got an R32 sedan and I found about 5+litres of water in the jack area of my boot :)

I have no idea as to where it's come from. The boot area is all dry, it's just the jack area and the other side.

It's been about a week since I sucked out all the water and it's rained quite a lot down here in Melbourne. I might check later today to see how much water is in there now.

i had the same problem a while back.

i took out the rubber grommets at the bottom of the sides of the boot and it poured out everywhere :D

i went to the car wash when it was all dry and after washing i found the leak was just under the tail lights. sort of where the boot bends 90 degrees.. (if you get what i mean?)

i got some silicone stuff for metal and went hack.

no more water! :)

Edited by dmr
i had the same problem a while back.

i took out the rubber grommets at the bottom of the sides of the boot and it poured out everywhere :)

i went to the car wash when it was all dry and after washing i found the leak was just under the tail lights. sort of where the boot bends 90 degrees.. (if you get what i mean?)

i got some silicone stuff for metal and went hack.

no more water! :D

I think I know what you're talking about. I remember washing the car awhile back and water used to keep coming out even though I've already dried the car from around the taillight area. I'll try and have a look when I get the time.

Do you have any pictures you can post to show exactly where you're talking about?

Cheers mate.

I think I know what you're talking about. I remember washing the car awhile back and water used to keep coming out even though I've already dried the car from around the taillight area. I'll try and have a look when I get the time.

Do you have any pictures you can post to show exactly where you're talking about?

Cheers mate.

here you go bud. sorry about the bad quality..

post-33759-1185174164_thumb.jpg

ive found a bit in the top of the boot where it also leaks through tho..i checked it thismorning and it seemed to be dripping through there and running down that side pocket..when it dries out ill put sum sikaflex on it an see what happens

  • 2 years later...

I was getting a leak from the boot seals, not the black rubber but the off white sealant on the body work near hydrolic lifting arms that hold the boot up.

Was only getting right hand side leaking but suppose the other side can be the same. The sealant goes hard and cracks. Difficult to see and detect as the leak can change with body temp.

I used to have a leak in my right hand side tail light, followed the DIY here & resealed the lights, however after I did that, water just started to flood the indicator & reverse light area & will eventually overflow to the boot through the opening where you reach to take/replace the light bulbs for the indicator & reverse lights, there seem to be a internal crack somewhere in the light assembly.

So I had to remove the whole tail light assembly again & drilled some holes on the bottom side so the water can just drain through.

Now I got no more leaks :D

So for anyone thinking of taking their tail light assembly out, you might as well drill some holes on the underside of it just in case & you can't really see the holes from the outside anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
×
×
  • Create New...