Jump to content
SAU Community

Mostly R31 Stuff (inc Rb20 Turbo And Smic)


Recommended Posts

Hey all...

Following spare parts for sale which I got with the wagon I picked up, plus some others I have accumulated

Located in Kallangur, Northside Brisbane, and best bet to see them is on weekends.

Preferred contact during Business hours is email timross__AT__serviceessentials.com.au or after hours on mobile 0401606223

Feel free to raise questions in this thread, HOWEVER be aware that it may take a day or two for me to reply, and if anyone gets in before you on the preferred contact methods above, stiff shit thats life

Anyways, most of these are ballpark figures but feel free to make a reasonable offer if my pricing seems unreasonable:

Turbo off RB20 red top, very little side to side shaft play, no front to rear shaft play (inc actuator): $200 (might also have a spare stock dump pipe maybe)

Stock RB20 sidemount intercooler: $50

PRICE DROP - Turbo $170, or $200 with SMIC

Pair stock front Springs: FREE

Charcoal Cannister: FREE

Various Door Glass and wagon rear side glass: $20ea

Window Winder rails: FREE

Pair front struts w/ stock springs and lower control arms: $40

Pair S3 headlights: $150

Pair Electric Mirrors: $60

Pair Manual Mirrors: $30

S3 Front Bumper: $100

Steering Rack: $60

Stock intank Fuel Pump: $30

Washer Bottle: $20

Auto Tailshaft (have 2x): $40ea

Power Steering Pump: $30

Master Cylinder: $20

A/C Compressor: $50

4 Guage Dash Cluster: $30

Windscreen Wiper Motor: $20

A/C Condensor Fan: $30

RB30 AFM (x2): $20 each

RB30 ECU (Manual): $40

Have 2 other RB30 ECU's here, not sure what they are, still have part numbers on them: $30each

Wiper Switch (which includes adjustable intermittent speed): $20

Simota Pod Filter in VGC: $20

Front and rear seats (blue) in VGC (no stains/burns/tears/cuts): $40 the lot

Edited by retox
Link to comment
Share on other sites

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Yes, I've been thinking about how to fabricate something. Either how OP did it with an alloy sheet or more complicated. Because of the CD shifter protrusion I think I will need to build a raised aluminum box to clear, then I would reutilize the same OE seal just shifted back. When I went on my test drive I popped open the EWG and exhaust just filled the cabin, so it will need to be closed up.
    • Car is struggling to rev from idle when you accelerate normally to spirited, But it will get past 1000ish rpm if you feather it, and then is fine so long as the revs don’t drop again. Idles fine. Plugs come out wet as after a few min.  Things changed are: CAS, ARM and fuel reg from a engine that was confirmed working 2 years ago Injectors have been reconditioned  ECU has no codes Where to from here? Video of the issue can be seen here  
    • I am trying to get an aftermarket exhaust and browsing the threads for opinions. But most of them are almost over 10 years old. Just tryna look and see what exhaust setups people are using nowadays and what are yall opinions on them. Really want to find one that sounds nice and not as quiet as the stock but does not scream rice.  
    • Approx 1m long, chrome moly, hardy splicer unis. Didn’t measure the diameter. The shop that built it also builds the shafts for b2r, jem, maatouks, etc and built the shaft to the same specs as their cars that’s are running 7 and 8 second passes!! Which say to me that it can handle some big mph 
    • You can't stall an engine at high speed.
×
×
  • Create New...