Jump to content
SAU Community

Recommended Posts

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

Great pics guys, sounds like everyone there enjoyed themselves and liked the route chosen (some of my favourite roads :)

SORRY again i couldn't make it, partners grandmother went to hospital late Friday night and didn't think it would be fair to be out and about all weekend :)

I hear my ride didn't show up anyway so i will be having words with him :thumbsup: probably better i didn't go with ya cause you would of blown the breatho still ya pissed kent :)

Already working on another one which i will be there in my own car (guarantee that) and hopefully those who couldn't make this one will be able to make the next >_<

Cheers GMB

Good to see you liked the ride Damo, your passanger footwell might need the feet dents fixed :D . The slow ol 4 door managed to lose the 300rwkw Bannamobile through the twisties :(

Taz said the footage didn't turn out that well :)

Edited by sav man

na the footage looks slow as, would have been worse in one of thoes gtr's

i think dimmi will make a short clip, maybe 3 mins out of the hour of footage we got.

it will be interesting to see how the new suspension goes. the granet sticks in the rear may make it worse.

nice photoes everyone.

a short run up to powatena may be the go next time. we could have lunch at the grate lake pub. i think its all sealed up to it.

Good to see you liked the ride Damo, your passanger footwell might need the feet dents fixed >_< . The slow ol 4 door managed to lose the 300rwkw Bannamobile through the twisties :D

Taz said the footage didn't turn out that well :(

the straights benny the straights :) ..........the twisties were too much fun! got the car out of shape too much. would of made the video very interesting if the camera car was behind some cars through that part of the road!.......but we had to start work!......what can you do! :whistling:

Edited by nizmokid
Ok guys here's the vid that we've done.

Note: not everybody is in the video due to lack of footage and pics but i think i made do with what i had.

Hope you all like it. :(

well put together..

Edited by woolls

well the pack caught the supra... even given the head start.... and arrived in lonnie together :huh:

pack = 2 gtrs/ 200sx/silver 4 door/ black 2 door r32 gtst

:thumbsup: was a wikid day ..

and nice video i hope to be putting another up in the next few days

Ben

yeah i was running low on fuel so i stopped pushing it so i could make it to scottsdale. >_<

Not to mention a damn 30 year old bus in my way.

just teasing ya mate.... >_<

u got a turbo on your machine?

the truth is that supras are as bad as american cars. they dont like corners.

na not realy.

i think it was a slowish trip back for ben and i as we didnt brake the speed limit. we just went 100 around corners. >_<

was a good day and a good vidio pitty about my filming. >_<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...